物品名称 规格型号 数量 单位 描述
| 内六角螺栓 | 直径":"M16","长度":"190m | 1600.00 | 个 | {"直径":"M16","长度":"190mm","图号":"无","螺纹长度":"50±2mm","材质":"45#碳钢","表面处理":"发黑热处理","性能等级":"12.9级","使用寿命":"60天","参照标准":"GB/T 16938-2008","备注":"产品完好无破损并符合上述技术要求，附带合格证。不合格品处理标准：如果到货物资不符合技术要求，予以换货处理，产生的费用由供货商负责。"} |
| 双头螺栓 | 直径":"M30","长度":"300m | 50.00 | 套 | {"直径":"M30","长度":"300mm","图号":"无","螺纹长度":">100mm","材质":"中碳钢","表面处理":"热处理(淬火、回火)","性能等级":"10.9","使用寿命":">180天","参照标准":"GB/T 5780-2000、GB/T 5781-2000、GB/T 5782-2000、GB/T 5783-2000","备注":"螺栓螺纹为细丝螺纹，螺距2mm，并配双螺帽带弹簧垫"} |
| 弹簧 | 105*20*30*235 | 52.00 | 个 | {"规格型号":"105*20*30*235","材质":"弹簧钢","所属设备":"成型机","设备型号":"10b/h","设备生产厂家":"****公司","国产/进口":"国产","使用寿命":"730天","特殊要求":"无","参照标准":"GB/T 23935-2009","备注":"弹簧外径105mm,高度235mm,线径20mm,****中心距离:30mm"} |
| 弹垫 | 直径":"M10","材质":"弹簧钢" | 4000.00 | 个 | {"直径":"M10","材质":"弹簧钢","性能等级":"8.8"} |
| 不锈钢弹簧垫 | 直径":"M12","材质":"不锈钢3 | 2000.00 | 个 | {"直径":"M12","材质":"不锈钢316","使用寿命":"730天"} |
| 不锈钢外六角螺丝 | 直径":"M6","长度":"25mm" | 30000.00 | 个 | {"直径":"M6","长度":"25mm","图号":"M6*25","螺纹长度":"25mm","材质":"不锈钢304","表面处理":"0","性能等级":"A2-70","使用寿命":"360天","参照标准":"GB/T 3098.6-2014","备注":"全丝螺栓,螺丝丝扣均匀,无断丝,缺丝现象"} |
| 六角法兰面螺栓 | 直径":"M12","长度":"30", | 2000.00 | 个 | {"直径":"M12","长度":"30","图号":"/","螺纹长度":"30mm","材质":"304不锈钢","表面处理":"无","性能等级":"A2-70","使用寿命":"1095天","特殊要求":"无","参照标准":"GB/T 5789","备注":"产品完好无破损，符合上述技术要求，附带合格证。不合格品处理标准：如到货不符合技术要求，由供应商无条件进行更换、退货。"} |
| 平垫圈A级 | 直径":"M12","厚度":"2.5" | 2000.00 | 个 | {"直径":"M12","厚度":"2.5","材质":"304不锈钢","表面处理":"不处理","性能等级":"200HV","使用寿命":"1095天","参照标准":"GB/T 97.1","备注":"平垫圈A级/φ12/200HV/304不锈钢/产品完好无破损，符合上述技术要求，附带合格证。不合格品处理标准：如到货不符合技术要求，由供应商无条件进行更换、退货。"} |
| I型六角螺母 | 直径":"M12","高度":"10.8 | 2000.00 | 个 | {"直径":"M12","高度":"10.8","材质":"304不锈钢","表面处理":"无","性能等级":"A2-70","使用寿命":"1095天","参照标准":"GB/T 6170","备注":"产品完好无破损，符合上述技术要求，附带合格证。不合格品处理标准：如到货不符合技术要求，由供应商无条件进行更换、退货。"} |
| 螺母 | 直径":"M6mm","高度":"5.2 | 4000.00 | 个 | {"直径":"M6mm","高度":"5.2mm","材质":"Q235","表面处理":"氧化","性能等级":"4级","使用寿命":"不小于730天","参照标准":"GB/T 41-2016","备注":"1、产品外观完好、无腐蚀、锈迹；\n2、如与技术要求不符，执行退换货处理，所产生的费用由供应商承担。"} |
| 外六角螺栓 | 直径":"M6","长度":"100mm | 4000.00 | 个 | {"直径":"M6","长度":"100mm","图号":"M6*100","螺纹长度":"45mm","材质":"碳钢","表面处理":"镀锌","性能等级":"无","使用寿命":"365天","参照标准":"GB/T 5782-2016","备注":"螺丝丝扣均匀,非全丝,无断丝.缺丝现象."} |
| 膨胀螺丝 | M8*60 | 100.00 | 套 | {"规格型号":"M8*60","直径":"12mm","长度":"60mm","强度等级":"4.8级","表面处理":"镀蓝白锌","材质要求":"碳钢","配套附件":"螺帽、垫片","参照标准":"GB/T 22795-2008","备注":"1、产品及配件外观完好、无腐蚀、锈迹；\n2、如与技术要求不符，执行退换货处理，所产生的费用由供应商承担。"} |
| 螺帽 | 直径":"8","材质":"45#碳钢" | 4000.00 | 个 | {"直径":"8","材质":"45#碳钢","性能等级":"8.8","使用寿命":"3月","参照标准":"GB/T 3098.1-2010"} |
| 螺帽 | 直径":"6","材质":"中碳钢并经过 | 4000.00 | 个 | {"直径":"6","材质":"中碳钢并经过热处理","性能等级":"8.8","使用寿命":"12月","参照标准":"GB/T 1229-2006"} |
| 螺帽 | 直径":"14mm","材质":"45# | 2000.00 | 个 | {"直径":"14mm","材质":"45#碳钢","性能等级":"12.9","使用寿命":"≥6月","参照标准":"GB/T 18230.2-2000"} |
| 螺母 | 直径":"M12","高度":"10.6 | 2000.00 | 个 | {"直径":"M12","高度":"10.6mm","材质":"45#碳钢","表面处理":"表面氧化发黑","性能等级":"8.8","使用寿命":"≥365天","参照标准":"GB/T 16938-2008","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} |
| 外六角螺母 | 直径":"M10","高度":"8.04 | 2000.00 | 个 | {"直径":"M10","高度":"8.04~8.4mm","材质":"45#碳钢","表面处理":"发黑","性能等级":"8","使用寿命":"1460天","参照标准":"GB/T 6170-2015","备注":"如到货与技术要求不符,由供应商无条件进行退,换货处理"} |
| 螺丝 | 直径":"8","长度":"30","材 | 2000.00 | 个 | {"直径":"8","长度":"30","材质":"45#钢","性能等级":"8.8级","参照标准":"GB/T 18230.1-2000"} |
| 螺丝 | 直径":"6","长度":"30±1mm | 2000.00 | 个 | {"直径":"6","长度":"30±1mm","螺纹长度":"5.9±0.05mmmm","材质":"Q235","性能等级":"4.8级"} |
| 外六角螺栓 | 直径":"6","长度":"50mm", | 2000.00 | 个 | {"直径":"6","长度":"50mm","螺纹长度":"50mm","材质":"碳钢","表面处理":"发蓝处理","性能等级":"8.8","参照标准":"GB/T 5782-2016"} |
| 外六角螺栓 | 直径":"M12","长度":"50mm | 2000.00 | 个 | {"直径":"M12","长度":"50mm","图号":"无","螺纹长度":"50mm","材质":"45#钢","表面处理":"发黑处理","性能等级":"8.8级","使用寿命":"90天","参照标准":"GB/T 5783-2016","备注":"来货带合格证,若到货与技术要求不符,由供应商无条件退换."} |
| 外六角螺栓 | 直径":"8","长度":"50","螺 | 2000.00 | 个 | {"直径":"8","长度":"50","螺纹长度":"半丝","材质":"碳钢","性能等级":"8.8"} |
| 外六角螺栓 | 直径":"10","长度":"50"," | 2000.00 | 个 | {"直径":"10","长度":"50","螺纹长度":"全丝","材质":"合金钢淬火并回火","性能等级":"12.9"} |
| 外六角螺栓 | 直径":"14","长度":"50"," | 2000.00 | 个 | {"直径":"14","长度":"50","螺纹长度":"全丝","材质":"中碳钢","表面处理":"发黑","性能等级":"8.8"} |
| 外六角螺丝 | 直径":"M12","长度":"60mm | 500.00 | 套 | {"直径":"M12","长度":"60mm","图号":"M12*60","螺纹长度":"29-31mm","材质":"Q235","表面处理":"发黑","性能等级":"8.8","使用寿命":"180天","参照标准":"GB/T 16938-2008","备注":"1.外观良好,无断丝、错丝.\n2.到货验收不符合技术要求,必须退换货,产生的费用由供应商承担."} |
| 平垫 | 直径":"10","材质":"Q235" | 200.00 | 个 | {"直径":"10","材质":"Q235","表面处理":"外表镀锌","使用寿命":"1年","参照标准":"GB/T 95-2002"} |
| 平垫 | 直径":"20","材质":"45H碳钢 | 400.00 | 个 | {"直径":"20","材质":"45H碳钢","性能等级":"黑"} |
| 螺栓 | 直径":"12","长度":"100", | 100.00 | 个 | {"直径":"12","长度":"100","材质":"Q235B","性能等级":"4.8级"} |
| 平垫 | 直径":"M16","厚度":"2mm" | 400.00 | 个 | {"直径":"M16","厚度":"2mm","材质":"65Mn钢","表面处理":"表面镀锌","性能等级":"200HV","使用寿命":"365天","参照标准":"GB/T 3098.26-2021","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} |
| 膨胀螺丝 | M8*60 | 2400.00 | 套 | {"规格型号":"M8*60","直径":"12mm","长度":"60mm","强度等级":"4.8级","表面处理":"镀蓝白锌","材质要求":"碳钢","配套附件":"螺帽、垫片","参照标准":"GB/T 22795-2008","备注":"1、产品及配件外观完好、无腐蚀、锈迹；\n2、如与技术要求不符，执行退换货处理，所产生的费用由供应商承担。"} |
| 高强螺栓 | 直径":"16","长度":"60"," | 20.00 | 个 | {"直径":"16","长度":"60","螺纹长度":"60mm","材质":"低碳合金钢或中碳钢并经过热处理","性能等级":"10.9"} |
| 外六角螺丝 | 直径":"M8","长度":"50mm" | 40.00 | 个 | {"直径":"M8","长度":"50mm","螺纹长度":"50mm","材质":"碳钢","性能等级":"4.8级","使用寿命":"730天"} |
| 高强螺帽 | 直径":"M20","高度":"18mm | 180.00 | 个 | {"直径":"M20","高度":"18mm","材质":"45#碳钢","表面处理":"氧化","性能等级":"12.9","使用寿命":"不小于730天","参照标准":"GB/T 41-2016","备注":"1、产品外观完好、无腐蚀、锈迹；\n2、如与技术要求不符，执行退换货处理，所产生的费用由供应商承担。"} |
| 螺帽 | 直径":"14mm","材质":"45# | 500.00 | 个 | {"直径":"14mm","材质":"45#碳钢","性能等级":"12.9","使用寿命":"≥6月","参照标准":"GB/T 18230.2-2000"} |
| 镀锌平垫 | 直径":"14","材质":"钢，表面镀 | 250.00 | 个 | {"直径":"14","材质":"钢，表面镀锌"} |
| 平垫 | 直径":"30","材质":"65Mn钢 | 430.00 | 个 | {"直径":"30","材质":"65Mn钢"} |
| 外六角螺栓 | 直径":"20","长度":"130", | 180.00 | 个 | {"直径":"20","长度":"130","材质":"碳钢","性能等级":"8.8"} |
| 外六角螺栓 | 直径":"M14","长度":"180m | 250.00 | 个 | {"直径":"M14","长度":"180mm","材质":"碳钢","性能等级":"8.8","参照标准":"GB/T 3098.1-2010"} |
| 拉铆钉 | Ф4*16 | 10.00 | 千克 | {"规格型号":"Ф4*16","材质":"铝壳铁芯","使用寿命":"3-5月","参照标准":"GB/T 3098.19-2004"} |
| 平垫 | 直径":"M22","厚度":"3mm" | 100.00 | 个 | {"直径":"M22","厚度":"3mm","材质":"Q235B","表面处理":"镀锌","性能等级":"100HV","使用寿命":"≥365天","参照标准":"GB/T 95-2002","备注":"验收标准:到货与技术要求不符时,供应商无条件退换货处理。"} |
| 螺帽 | M20 | 37.00 | 个 | {"直径":"M20","高度":"12.5mm","材质":"Q235","表面处理":"防锈处理","性能等级":"4.8","使用寿命":"720天","参照标准":"GB/T 41-2016","备注":"螺帽，规格20*12.5，材质Q235，表面防锈处理，参考标准GB/T 41-2016，不合格处理标准:如到货不符合技术要求,由供应商无条件进行更换,退货处理."} |
| 外六角螺母 | 直径":"M16","高度":"15.9 | 284.00 | 个 | {"直径":"M16","高度":"15.9mm","材质":"45#碳钢","表面处理":"无","性能等级":"8.8级","使用寿命":"730天","参照标准":"GB/T 6170-2015","备注":"如不符合技术要求供应商予以无条件退换处理。"} |
| 双头螺栓 | 直径":"M20","长度":"120m | 200.00 | 个 | {"直径":"M20","长度":"120mm","图号":"无","螺纹长度":"≥45mm","材质":"碳钢","表面处理":"无","性能等级":"4.8级","使用寿命":"730天","特殊要求":"1.两端螺纹长度≥45mm,螺距:2.5mm,2.国产通用件.3.验收标准:如到货与技术要求不符,供应商应无条件进行退,换货处理.","参照标准":"GB/T 953-1988"} |
| 沉头螺栓 | 直径":"M16","长度":"50mm | 29.00 | 个 | {"直径":"M16","长度":"50mm","图号":"无","螺纹长度":"40mm","材质":"Q235","表面处理":"镀锌或发黑处理","性能等级":"4.8级","使用寿命":"≥180天","参照标准":"GB/T 3098.1-2010","备注":"粗牙牙距2mm,不符合技术要求,予以退换货处理,产生的费用由供货商承担."} |
| 镀锌螺帽 | 直径":"M8mm","高度":"6.5 | 2000.00 | 个 | {"直径":"M8mm","高度":"6.5mm","材质":"45#钢","表面处理":"镀锌","性能等级":"4.8级","使用寿命":"＞1095天","参照标准":"GB/T 41-2016","备注":"当验收不符合技术要求时，需进行退换货处理，期间所产生的运输费用由供货商承担。"} |
| 镀锌全丝杆 | 直径":"M0.008","长度":"3 | 300.00 | 支 | {"直径":"M0.008","长度":"3000mm","材质":"Q235","表面处理":"镀锌,螺纹清晰,镀锌层不应有剥离,起皮,凸起,花斑,伤痕等现象","使用寿命":"3650天","性能等级":"4.8"} |
| 镀锌全丝杆 | 直径":"M0.008","长度":"3 | 2500.00 | 支 | {"直径":"M0.008","长度":"3000mm","材质":"Q235","表面处理":"镀锌,螺纹清晰,镀锌层不应有剥离,起皮,凸起,花斑,伤痕等现象","使用寿命":"3650天","性能等级":"4.8"} |
| 铁排钉 | 长度":"45mm","直径":"Φ2. | 2000.00 | 千克 | {"长度":"45mm","直径":"Φ2.1mm","表面处理":"涂胶均匀","材质":"Q235","允许偏差":"±1mm","特殊要求":"1、外观应光洁无锈蚀、无伤痕、排列整齐、涂胶均匀，无开胶断裂情况。2、排钉直径2.1±1mm，钉帽宽度6mm，长度公差±1mm。3、排版平整无明显凹凸不平现象、无胶赘，弹夹可顺利滑动关闭。","参照标准":"GB/T 701-2008","备注":"使用寿命：车间生产易耗品"} |
| 铁排钉 | 长度":"50mm","直径":"Φ2. | 1000.00 | 千克 | {"长度":"50mm","直径":"Φ2.1mm","表面处理":"涂胶均匀","材质":"Q235","允许偏差":"±0.1mm","特殊要求":"1、外观应光洁无锈蚀、无伤痕、排列整齐、涂胶均匀，无开胶断裂情况。2、排钉直径2.1±0.1mm，钉帽宽度6mm，长度公差±1mm。3、排版平整无明显凹凸不平现象、无胶赘，弹夹可顺利滑动关闭。","参照标准":"GB/T 701-2008","备注":"如发现质量不合格产品，予以退换货处理\n使用年限：车间一次性使用辅材"} |
| 卷钉 | 材质":"Q235","外观":"螺纹卷 | 300.00 | 箱 | {"材质":"Q235","外观":"螺纹卷钉","直径":"φ2.8mm","长度":"75mm","表面处理":"浸漆处理","特殊要求":"钉径公差±0.2mm,钉长公差±3mm","参照标准":"GB/T 27704-2011","备注":"每箱20卷卷钉，每卷225支钉\n使用寿命;车间生产易耗品一次性辅材.\n发现质量不合格产品或与技术标准不符，进行退换货处理,期间产生费用由供货商承担."} |
| 双头螺栓 | 直径":"M20","长度":"230m | 130.00 | 套 | {"直径":"M20","长度":"230mm","图号":"无","螺纹长度":">65mm","材质":"中碳钢","表面处理":"热处理（淬火、回火）","性能等级":"10.9","使用寿命":"180天","参照标准":"GB/T 5780-2000、GB/T 5781-2000、GB/T 5782-2000、GB/T 5783-2000","备注":"配2个螺帽及2个弹簧垫"} |
| 镀锌螺帽 | 直径":"12","材质":"低碳钢，外 | 24000.00 | 个 | {"直径":"12","材质":"低碳钢，外表面镀锌","性能等级":"4.8"} |
| 镀锌外六角螺栓 | 直径":"11MM±0.5MM","长度 | 21000.00 | 个 | {"直径":"11MM±0.5MM","长度":"180MM±4MM","材质":"Q235","表面处理":"镀锌","性能等级":"4.8级","参照标准":"GB/T 5781-2000"} |
| 钻尾自攻自钻螺钉 | 直径":"5.5","长度":"25", | 1500.00 | 个 | {"直径":"5.5","长度":"25","材质":"CH1022A","性能等级":"4.8","表面处理":"电镀","特殊要求":"外观完好、平整、光洁、无毛刺、镀层光亮、丝扣均匀，断丝、偏心等不合格率＜5%。","参照标准":"GB/T 15856.4-2002","备注":"1.本品为消耗性材料2.到货物资若与技术要求不符，供货商应无条件退换货处理。"} |
| 高强螺帽 | 直径":"M16","高度":"14.4 | 300.00 | 个 | {"直径":"M16","高度":"14.4mm","材质":"中碳钢","表面处理":"发黑处理","性能等级":"8.8级","使用寿命":"≥365天","参照标准":"GB/T 16938-2008","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} |
| 外六角螺丝 | 直径":"M16","长度":"75", | 300.00 | 个 | {"直径":"M16","长度":"75","螺纹长度":"75mm","材质":"中碳钢","性能等级":"8.8"} |
| 沉头螺栓 | 直径":"10","长度":"100", | 400.00 | 个 | {"直径":"10","长度":"100","螺纹长度":"0","材质":"低碳钢","使用寿命":"3年"} |
| 螺帽 | 直径":"18mm","材质":"45# | 419.00 | 个 | {"直径":"18mm","材质":"45#钢","性能等级":"12.9","使用寿命":"3月","参照标准":"GB/T 70.1-2008"} |
| 镀锌螺帽 | 直径":"12","材质":"低碳钢，外 | 336.00 | 个 | {"直径":"12","材质":"低碳钢，外表面镀锌","性能等级":"4.8"} |
| 高强螺帽 | 直径":"M24","高度":"20mm | 70.00 | 个 | {"直径":"M24","高度":"20mm","材质":"45#钢","表面处理":"发黑处理","性能等级":"8.8","使用寿命":"≥365天","参照标准":"GB/T 6170-2015","备注":"验货要求:如到货与技术要求不符,由供应商无条件进行退,换货处理."} |
| 镀锌螺帽 | 直径":"10mm","材质":"Q23 | 167.00 | 个 | {"直径":"10mm","材质":"Q235碳钢","使用寿命":"6-12个月以上月","参照标准":"GB/T 31559-2015"} |
| 弹垫 | 直径":"24","材质":"65锰弹簧 | 188.00 | 个 | {"直径":"24","材质":"65锰弹簧钢"} |
| 平垫 | 直径":"24","材质":"45H碳钢 | 534.00 | 个 | {"直径":"24","材质":"45H碳钢","使用寿命":"12月","参照标准":"GB/T 5286-1985"} |
| 不锈钢开口销 | Φ5*70 | 108.00 | 个 | {"规格型号":"Φ5*70","材质":"304不锈钢","使用寿命":"3年","参照标准":"GB/T 91-2000"} |
| 板锤螺栓 | 直径":"24","长度":"193", | 100.00 | 个 | {"直径":"24","长度":"193","螺纹长度":"150mm","材质":"45#钢","性能等级":"8.8","使用寿命":"1年","特殊要求":"头部椭圆形"} |
| 斗提螺栓 | 直径":"M10","长度":"50mm | 1000.00 | 个 | {"直径":"M10","长度":"50mm","图号":"无","螺纹长度":"35mm","材质":"Q235钢","表面处理":"发黑","性能等级":"8.8级","使用寿命":"120天","特殊要求":"每套螺栓配斗提专用垫一个、螺母一个","参照标准":"GB/T 16938-2008","备注":"到货不合格处理标准：如到货后验收不符合技术要求,供货商应免费给予退换货处理."} |
| 内六角螺丝 | 直径":"M20","长度":"140m | 42.00 | 个 | {"直径":"M20","长度":"140mm","材质":"45H钢","性能等级":"12.9","使用寿命":"365天"} |
| 螺帽 | 直径":"M10","高度":"8mm" | 300.00 | 个 | {"直径":"M10","高度":"8mm","材质":"碳钢10级，锰含量0.6%","表面处理":"发蓝发黑","性能等级":"10","使用寿命":"≥730天","参照标准":"GB/T 16938-2008","备注":"经热处理（淬火,回火），到货如不符合技术要求，予以退换货处理。"} |
| 螺母 | 直径":"M16mm","高度":"13 | 100.00 | 个 | {"直径":"M16mm","高度":"13.6mm","材质":"中碳钢","表面处理":"发黑处理","性能等级":"8.8","使用寿命":"≥365天","参照标准":"GB/T 6170-2015"} |
| 螺帽 | 直径":"M12","高度":"10.6 | 300.00 | 个 | {"直径":"M12","高度":"10.6mm","材质":"45#碳钢","表面处理":"发黑处理","性能等级":"8.8","使用寿命":"≥365天","参照标准":"GB/T 16938-2008","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} |
| 外六角螺栓 | 直径":"M16","长度":"50mm | 50.00 | 个 | {"直径":"M16","长度":"50mm","图号":"M16*50","螺纹长度":"50mm","材质":"45#钢","表面处理":"发黑处理","性能等级":"8.8级","使用寿命":"≥365天","参照标准":"GB/T 16938-2008","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} |
| 开口销 | Φ4*70 | 200.00 | 个 | {"规格型号":"Φ4*70","材质":"Q235","使用寿命":"6月","参照标准":"GB/T 91-2000"} |
| 平垫 | 直径":"50","厚度":"5","材 | 843.00 | 个 | {"直径":"50","厚度":"5","材质":"不锈钢","性能等级":"12.9级","使用寿命":"2月","参照标准":"JB/T8559-2014"} |
| 开口销 | Ф4*50 | 200.00 | 个 | {"规格型号":"Ф4*50","材质":"Q235表面热镀锌处理","参照标准":"GB/T 91-2000"} |
| 螺帽 | 直径":"M12","高度":"10.6 | 200.00 | 个 | {"直径":"M12","高度":"10.6mm","材质":"45#碳钢","表面处理":"发黑处理","性能等级":"8.8","使用寿命":"≥365天","参照标准":"GB/T 16938-2008","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} |
| 斗提螺栓 | 直径":"10","长度":"70mm" | 2000.00 | 个 | {"直径":"10","长度":"70mm","材质":"不锈钢","使用寿命":"6月"} |
| 沉头螺栓 | 直径":"M10","长度":"40mm | 500.00 | 个 | {"直径":"M10","长度":"40mm","图号":"无","螺纹长度":"34mm","材质":"碳钢","表面处理":"发黑","性能等级":"8.8级","使用寿命":"≥180天","参照标准":"GB/T 819.2-2016","备注":"螺距1.5mm，不符合技术要求予以退换货处理。"} |
| 螺帽 | 直径":"M10","高度":"8mm" | 1000.00 | 个 | {"直径":"M10","高度":"8mm","材质":"碳钢10级，锰含量0.6%","表面处理":"发蓝发黑","性能等级":"10","使用寿命":"≥730天","参照标准":"GB/T 16938-2008","备注":"经热处理（淬火,回火），到货如不符合技术要求，予以退换货处理。"} |
| 膨胀螺丝 | M12*100 | 200.00 | 套 | {"规格型号":"M12*100","直径":"16mm","长度":"100mm","强度等级":"4.8级","表面处理":"表面镀锌","材质要求":"Q235低碳钢","配套附件":"螺帽、垫片","参照标准":"GB/T 22795-2008","备注":"1、使用寿命：5年；\n2、产品外观无腐蚀，完好；\n3、如与技术要求不符，执行退换货处理，所产生费用由供应商承担。"} |
| 螺帽 | 直径":"M12","高度":"10.6 | 100.00 | 个 | {"直径":"M12","高度":"10.6mm","材质":"45#碳钢","表面处理":"发黑处理","性能等级":"8.8","使用寿命":"≥365天","参照标准":"GB/T 16938-2008","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} |
| 高强螺帽 | 直径":"20","材质":"45#钢" | 189.00 | 个 | {"直径":"20","材质":"45#钢","性能等级":"8.8","使用寿命":"2年"} |
| 高强螺栓 | 直径":"M20","长度":"90mm | 164.00 | 套 | {"直径":"M20","长度":"90mm","图号":"M20*90","螺纹长度":"90mm","材质":"中碳合金钢做热处理","表面处理":"发黑处理","性能等级":"10.9级","使用寿命":"720天","参照标准":"GB/T 16938-2008","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} |
| 外六角螺栓 | 直径":"M12","长度":"50mm | 200.00 | 个 | {"直径":"M12","长度":"50mm","图号":"无","螺纹长度":"50mm","材质":"45#钢","表面处理":"发黑处理","性能等级":"8.8级","使用寿命":"90天","参照标准":"GB/T 5783-2016","备注":"来货带合格证,若到货与技术要求不符,由供应商无条件退换."} |
| 弹簧 | 0.8*17.8*15 | 500.00 | 个 | {"规格型号":"0.8*17.8*15","材质":"60SI2MNA","所属设备":"除尘器","设备型号":"zz-1400","设备生产厂家":"国产","国产/进口":"国产","使用寿命":"≥365天","特殊要求":"长度：15mm；直径：17.8mm；钢丝直径：0.8mm；圈数：4圈","参照标准":"GB/T 2089-2009","备注":"验收标准：到货与技术要求不符时，供应商无条件退换货处理。"} |
| 全丝外六角螺丝 | 直径":"12","长度":"50"," | 200.00 | 个 | {"直径":"12","长度":"50","螺纹长度":"全丝","材质":"45#钢","性能等级":"4.8"} |
| 外六角螺栓 | 直径":"20","长度":"230", | 50.00 | 个 | {"直径":"20","长度":"230","螺纹长度":"半丝","材质":"低碳钢","性能等级":"4.8"} |
| 全丝螺栓 | 直径":"M14","长度":"60mm | 98.00 | 个 | {"直径":"M14","长度":"60mm","图号":"M14*60","螺纹长度":"60mm","材质":"中碳钢并经过热处","表面处理":"发黑处理","性能等级":"8.8","使用寿命":"≥365天","参照标准":"GB/T 16938-2008","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} |
| 外六角螺栓 | 直径":"12","长度":"75"," | 300.00 | 个 | {"直径":"12","长度":"75","螺纹长度":"全丝","材质":"Q235","性能等级":"4.8"} |
| 外六角螺丝 | 直径":"6mm","长度":"50mm | 178.00 | 个 | {"直径":"6mm","长度":"50mm","材质":"低碳钢"} |
| 外六角螺丝 | 直径":"12","长度":"70"," | 300.00 | 个 | {"直径":"12","长度":"70","螺纹长度":"全丝","材质":"Q235","性能等级":"4.8"} |
| 钢丝绳卡扣 | Φ15 | 36.00 | 个 | {"规格型号":"Φ15","材质":"45#钢，外部镀锌","使用寿命":"≥720天","参照标准":"GB/T 5976-2006","备注":"到货产品必须符合技术要求，达不到技术要求的厂家必须无条件退换货物。"} |
| 外六角螺丝 | 直径":"12","长度":"70mm" | 162.00 | 套 | {"直径":"12","长度":"70mm","螺纹长度":"全丝","材质":"45H碳钢","参照标准":"GB/T 3098.1-2010"} |
| 高强螺栓 | 直径":"30","长度":"190", | 50.00 | 个 | {"直径":"30","长度":"190","螺纹长度":"72mm","材质":"45#钢","参照标准":"GB/T 5782-2016"} |
| 方头螺栓 | 直径":"24mm","长度":"120 | 100.00 | 个 | {"直径":"24mm","长度":"120mm","螺纹长度":"70mm","材质":"45H碳钢","性能等级":"10.9级","使用寿命":"2~3月","参照标准":"GB/T 3098.1-2010"} |
| 镀锌螺帽 | 直径":"M5","材质":"Q235钢 | 5000.00 | 个 | {"直径":"M5","材质":"Q235钢"} |
| 螺栓 | 直径":"M10","长度":"60mm | 170.00 | 个 | {"直径":"M10","长度":"60mm","材质":"碳钢","性能等级":"8.8级","使用寿命":"300天"} |
| 外六角螺栓 | 直径":"M8","长度":"35mm" | 300.00 | 个 | {"直径":"M8","长度":"35mm","材质":"碳钢","性能等级":"4.8级","使用寿命":"1095天"} |
| 内六角螺栓 | 直径":"M10","长度":"55mm | 30.00 | 个 | {"直径":"M10","长度":"55mm","螺纹长度":"55mm","材质":"碳钢","性能等级":"8.8","使用寿命":"180天"} |
| 全丝外六角螺丝 | 直径":"MM6","长度":"30", | 300.00 | 个 | {"直径":"MM6","长度":"30","图号":"M6*30","螺纹长度":"30","材质":"碳钢","表面处理":"无","性能等级":"12.9","使用寿命":"90天","参照标准":"GB/T 3098.6-2014"} |
| 内卡簧 | Ф35 | 50.00 | 个 | {"规格型号":"Ф35","材质":"钢","使用寿命":"360天"} |
| 弹簧 | 2*33*100 | 20.00 | 个 | {"规格型号":"2*33*100","材质":"弹簧钢"} |
| 不锈钢双头螺栓 | 直径":"M16","长度":"150" | 32.00 | 个 | {"直径":"M16","长度":"150","图号":"M16","螺纹长度":"50mm","材质":"不锈钢304","表面处理":"无","性能等级":"8.8","使用寿命":"365天","特殊要求":"无","参照标准":"GB/T 3106-2016","备注":"验收标准:附带合格证,表面及螺纹无损伤,若不符合要求供货厂家要给予退货或换货."} |
| 不锈钢螺帽 | 直径":"M16","高度":"12.6 | 64.00 | 个 | {"直径":"M16","高度":"12.6mm","材质":"不锈钢304","表面处理":"无","性能等级":"A2-70","使用寿命":"≥365天","参照标准":"GB/T 3106-2016","备注":"验收标准:附带合格证,表面及螺纹无损伤,若不符合要求供货厂家要给予退货或换货."} |
| 平键 | 6*6 | 20.00 | 米 | {"型号":"6*6","宽度":"6mm","高度":"6mm","长度":"1000mm","材质":"Q235","使用寿命":"365天","参照标准":"GB/T 1096-2003","备注":"该到货产品与技术要求不符，对该到货产品进行10%处罚或调换退货，调换货产生的费用由供货方承担。"} |
| 平键 | 20*12 | 600.00 | 米 | {"型号":"20*12","宽度":"20mm","高度":"12mm","长度":"1000mm","材质":"Q235","使用寿命":"365天","参照标准":"GB/T 1096-2003","备注":"该到货产品与技术要求不符，对该到货产品进行10%处罚或调换退货，调换货产生的费用由供货方承担。"} |
| 平键 | 28*16 | 10.00 | 米 | {"型号":"28*16","宽度":"28mm","高度":"16mm","长度":"1000mm","材质":"Q235","使用寿命":"365天","参照标准":"GB/T 1096-2003","备注":"该到货产品与技术要求不符，对该到货产品进行10%处罚或调换退货，调换货产生的费用由供货方承担。"} |
| 平键 | 8*7 | 20.00 | 米 | {"型号":"8*7","宽度":"8mm","高度":"7mm","长度":"1000mm","材质":"Q235","使用寿命":"365天","参照标准":"GB/T 1096-2003","备注":"该到货产品与技术要求不符，对该到货产品进行10%处罚或调换退货，调换货产生的费用由供货方承担。"} |
| 平键 | 16*10 | 20.00 | 米 | {"型号":"16*10","宽度":"16mm","高度":"10mm","长度":"1000mm","材质":"碳钢Q235","使用寿命":"≥90天"} |
| 钻尾自攻自钻螺钉 | 直径":"5.5","长度":"25", | 7200.00 | 个 | {"直径":"5.5","长度":"25","材质":"CH1022A","性能等级":"4.8","表面处理":"电镀","特殊要求":"外观完好、平整、光洁、无毛刺、镀层光亮、丝扣均匀，断丝、偏心等不合格率＜5%。","参照标准":"GB/T 15856.4-2002","备注":"1.本品为消耗性材料2.到货物资若与技术要求不符，供货商应无条件退换货处理。"} |
| 螺栓 | 直径":"20","长度":"80mm" | 151.00 | 个 | {"直径":"20","长度":"80mm","螺纹长度":"80mm","材质":"低碳合金钢","性能等级":"8.8级","参照标准":"GB/T 5782-2016"} |
| 不锈钢螺丝 | 直径":"M12mm","长度":"50 | 1000.00 | 个 | {"直径":"M12mm","长度":"50mm","图号":"M12*50","螺纹长度":"50mm","材质":"不锈钢304","表面处理":"无","性能等级":"A2-70","使用寿命":"≥365天","参照标准":"GB/T 3098.6-2014","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} |
| 外六角螺丝 | 直径":"M8","长度":"40mm" | 200.00 | 套 | {"直径":"M8","长度":"40mm","图号":"M8*40","螺纹长度":"36-38mm","材质":"Q235","表面处理":"发黑","性能等级":"8.8","使用寿命":"180天","参照标准":"GB/T 16938-2008","备注":"1.外观良好,无断丝、错丝.\n2.到货验收不符合技术要求,必须退换货,产生的费用由供应商承担."} |
| 镀锌螺母 | 直径":"M12mm","高度":"10 | 136.00 | 个 | {"直径":"M12mm","高度":"10.8mm","材质":"45#钢","表面处理":"外表经镀锌钝化处理，镀层厚度5 um到8um","性能等级":"8级","使用寿命":"720天","参照标准":"GB/T 6170-2015","备注":"1.零部件供货时提供到货清单+合格证.\n2.如到货验收不符合技术要求，供货商无条件给予退换货处理，因此产生的费用由供货商承担."} |
| 外六角螺丝 | 直径":"16","长度":"150", | 50.00 | 个 | {"直径":"16","长度":"150","材质":"碳钢","性能等级":"8.8"} |
| 高强螺帽 | 直径":"M16","高度":"14.4 | 32.00 | 个 | {"直径":"M16","高度":"14.4mm","材质":"中碳钢","表面处理":"发黑处理","性能等级":"8.8级","使用寿命":"≥365天","参照标准":"GB/T 16938-2008","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} |
| 不锈钢弹簧垫 | 直径":"M14mm","厚度":"9m | 9.00 | 个 | {"直径":"M14mm","厚度":"9mm","材质":"不锈钢304","表面处理":"硬度不低于HB205","性能等级":"A2-70","使用寿命":"365天","参照标准":"GJB 5862.2-2006"} |
| 铁钉 | 长度":"100±5mm","直径":" | 6000.00 | 千克 | {"长度":"100±5mm","直径":"4±0.3mm","表面处理":"圆钉应经磨光处理，磨光后的圆钉表面应该是清洁和光亮并无显著伤痕。高强度，耐腐蚀，高硬度；","材质":"Q235","特殊要求":"钉帽：（8-10）mm;圆钉的次钉率和废钉率的总和不得超过8%；废钉率不得超过5%；"} |
| 内六角螺栓 | 直径":"6","长度":"60mm", | 2000.00 | 个 | {"直径":"6","长度":"60mm","材质":"45H碳钢","性能等级":"12.9","使用寿命":"6-12月","参照标准":"GB/T 3098.1-2010"} |
| 镀锌螺帽 | 直径":"M6mm","高度":"5mm | 6000.00 | 个 | {"直径":"M6mm","高度":"5mm","材质":"45#钢","表面处理":"镀锌","性能等级":"4.8级","使用寿命":"＞1095天","参照标准":"GB/T 41-2016","备注":"当验收不符合技术要求时，需进行退换货处理，期间所产生的运输费用由供货商承担。"} |
| 镀锌螺帽 | 直径":"10mm","材质":"Q23 | 100.00 | 个 | {"直径":"10mm","材质":"Q235碳钢","使用寿命":"6-12个月以上月","参照标准":"GB/T 31559-2015"} |
| 平垫 | 直径":"M12","厚度":"1.7m | 6000.00 | 个 | {"直径":"M12","厚度":"1.7mm","材质":"65Mn钢","表面处理":"外表镀锌","性能等级":"4.8","使用寿命":"≥365天","参照标准":"GB/T 3098.26-2021","备注":"1、外观良好\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} |
| 平垫 | 直径":"M14","厚度":"2mm" | 2000.00 | 个 | {"直径":"M14","厚度":"2mm","材质":"Q235","表面处理":"镀锌","性能等级":"8.8级","使用寿命":"不小于365天","参照标准":"GB/T 95-2002","备注":"1、产品外观完好、无腐蚀、锈迹，厚度均匀，边缘光滑；\n2、如与技术要求不符，执行退换货处理，所产生的费用由供应商承担。"} |
| 内六角螺丝 | 直径":"6","螺纹长度":"20mm | 4000.00 | 个 | {"直径":"6","螺纹长度":"20mm","材质":"45#钢","性能等级":"8.8"} |
| 外六角螺栓 | 直径":"M12","长度":"35mm | 500.00 | 个 | {"直径":"M12","长度":"35mm","材质":"低碳钢","性能等级":"4.8级","使用寿命":"180天","参照标准":"GB/T 5782-2016"} |
| 不锈钢螺帽 | 直径":"M12","高度":"10mm | 300.00 | 个 | {"直径":"M12","高度":"10mm","材质":"不锈钢316L","使用寿命":"365天"} |
| 不锈钢沉头螺丝 | M6mm | 1000.00 | 个 | {"直径":"M6mm","长度":"25mm","图号":"无","螺纹长度":"21mm","材质":"304不锈钢","表面处理":"酸洗，光亮","性能等级":"A2-70","使用寿命":"730天","参照标准":"GB/T 3098.6-2014","备注":"规格：M6*1*25mm，外观：不能有毛刺，不得有裂纹和明显缺陷 设备紧固件，到货物资达不到技术要求，供货厂家无偿退换货，退换货所产生的费用由厂家自行承担。"} |
| 热镀锌螺帽 | 直径":"M14","高度":"12.1 | 6500.00 | 个 | {"直径":"M14","高度":"12.1~12.8mm","材质":"Q235","表面处理":"热镀锌","性能等级":"6级","使用寿命":"4380天","参照标准":"GB/T 6170-2015","备注":"热镀锌按照GB/T5267.3执行，来货必须附有产品材质证明（合格证），来货验收达不到技术要求，供货商应无条件给予退换货处理。（退换货产生的一切费用由供货商承担）"} |
| 钻尾自攻自钻螺钉 | 直径":"5.5mm","长度":"50 | 38000.00 | 个 | {"直径":"5.5mm","长度":"50mm","材质":"CH1022A","表面处理":"电镀","参照标准":"GB/T15856.4-2002"} |
| 钻尾自攻自钻螺钉 | 直径":"5.5","长度":"25", | 216000.00 | 个 | {"直径":"5.5","长度":"25","材质":"CH1022A","性能等级":"4.8","表面处理":"电镀","特殊要求":"外观完好、平整、光洁、无毛刺、镀层光亮、丝扣均匀，断丝、偏心等不合格率＜5%。","参照标准":"GB/T 15856.4-2002","备注":"1.本品为消耗性材料2.到货物资若与技术要求不符，供货商应无条件退换货处理。"} |
| 钻尾自攻自钻螺钉 | 直径":"5.5mm","长度":"75 | 22000.00 | 个 | {"直径":"5.5mm","长度":"75mm","材质":"CH1022A","性能等级":"4.8级","表面处理":"电镀，镀层光亮","特殊要求":"无","参照标准":"GB/T 156856.4-2002"} |
| 热镀锌螺帽 | 直径":"M12mm","高度":"10 | 21450.00 | 个 | {"直径":"M12mm","高度":"10.8mm","材质":"不锈钢","表面处理":"热镀锌","性能等级":"4.8级","使用寿命":"4380天","参照标准":"GB/T 13912-2002","备注":"本品使用寿命:12年,热镀锌螺帽/12mm/不锈钢/热镀锌/4.8级/ITE个/GB/T 13912-2002"} |
| 外六角螺栓 | 直径":"M12","长度":"50mm | 200.00 | 个 | {"直径":"M12","长度":"50mm","图号":"无","螺纹长度":"50mm","材质":"45#钢","表面处理":"发黑处理","性能等级":"8.8级","使用寿命":"90天","参照标准":"GB/T 5783-2016","备注":"来货带合格证,若到货与技术要求不符,由供应商无条件退换."} |
| 内六角螺丝 | 直径":"M30","长度":"200m | 8.00 | 个 | {"直径":"M30","长度":"200mm","螺纹长度":"200mm","材质":"45#钢","性能等级":"12.9","使用寿命":"240天"} |
| 全丝内六角螺丝 | 直径":"M6mm","长度":"25m | 200.00 | 套 | {"直径":"M6mm","长度":"25mm","图号":"M6*25","螺纹长度":"25mm","材质":"碳钢","表面处理":"发黑处理","性能等级":"12.9级","使用寿命":"不低于150天","参照标准":"GB/T 3098.1-2010"} |
换一批
换一批