物品名称 规格型号 数量 单位 描述
| 压渣机下压油缸 | 200/125*900 | 2.00 | 个 | {"规格型号":"200/125*900","图号":"无","材质":"活塞活塞杆导向套缸筒为45#钢,活塞杆表面镀铬","压力":"16MPa","行程":"900","活塞杆直径":"125mm","活塞直径":"200mm","密封件材质":"O型圈采用丁晴橡胶,活塞封采用PTFE，导向套轴封采用PTFE+聚氨酯防尘圈为聚氨酯","接口尺寸":"M24*1.5","所属设备名称":"压渣机","设备型号":"701S","设备生产厂家":"阿尔泰克","国产/进口":"进口","使用寿命":"1095天","特殊要求":"无","计量单位":"ITE","参照标准":"JB/T 10205-2010","备注":"销轴孔径φ38㎜、轴孔中心至轴端74㎜,****中心距305㎜\n螺栓孔径φ32㎜ \n厚度：43㎜\n油管接头：M24*1.5\n缸筒一端与缸底焊接,另一端与方形端盖焊接并采用内螺纹封堵导向套,活塞与活塞杆采用螺纹固定连接。 \n到货验收：包装完好，外观完好无损，带有合格证。如所送到物品不符合技术要求或质量不合格，供货商必须无条件退换货，由此产生的费用由供货商负责。"} |
| 轧机油缸 | TC50A250-ABD-EKM-20/S11D03378 | 1.00 | 个 | {"规格型号":"TC50A250-ABD-EKM-20/S11D03378","材质":"碳钢","压力":"13.7MPa","行程":"250mm","活塞杆直径":"35.5mm","活塞直径":"50mm","密封件材质":"NBR","接口尺寸":"Rc1/2","所属设备名称":"1+4轧机","设备型号":"2350mm","设备生产厂家":"IHI","使用寿命":"1095天","特殊要求":"试验压力:20.7MPa,若备件不符合技术要求,厂家应及时予以退换货,由此产生的费用由供货方承担","计量单位":"ITE"} |
| 液压缸 | CDH1MT4063/036/1065 | 1.00 | 个 | {"规格型号":"CDH1MT4/63/036/1065","图号":"****872791","材质":"45钢","压力":"160bar","行程":"1065","活塞杆直径":"36mm","活塞直径":"63mm","密封件材质":"丁腈橡胶+聚氨酯","接口尺寸":"M40","所属设备名称":"推进式加热炉","设备型号":"ST0g990/283/1833Al","设备生产厂家":"艾伯纳工业炉厂","国产/进口":"国产","使用寿命":"365天","特殊要求":"无","计量单位":"ITE","参照标准":"JB/T 10205-2010","备注":"1、到货后包装完整无破损\n2、液压缸油口进行封堵\n3、到货后备件不符合技术要求需退换货处理，产生费用由供货商承担"} |
| 气缸 | RA/8200/M/250 | 1.00 | 个 | {"型号":"RA/8200/M/250","规格尺寸":"行程：250mm；缸径：200mm；接口尺寸：G3/4","工作方式":"单杆双作用","适用介质":"空气","计量单位":"ITE"} |
| 复动型气缸 | SE125B*250-TC-H | 10.00 | 个 | {"型号":"SE125B*250-TC-H","规格尺寸":"125mm*250mm","工作方式":"双作用","适用介质":"压缩空气","适用设备":"EFR制造的60T扁锭均质炉","计量单位":"ITE"} |
| 气缸 | 1562.****.1 | 20.00 | 个 | {"型号":"1562.****.1","规格尺寸":"缸径:63mm,行程:20mm","工作方式":"双作用式","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"厚板横剪堆垛机","国内/国外":"国内","生产厂家":"通用设备","计量单位":"ITE","参照标准":"GB/T 32336-2015","备注":"1.缸体材质:铝合金,活塞杆:AISI303不锈钢.2.气缸内置磁环:通过接近开关检测,工作压力:2-10bar.3.使用寿命:正常使用不低于180天.4.验收标准:产品有合格证明,产品完好无破损并符合上述技术要求.活塞杆活动运行顺畅.气密性良好.5.升级型号或替代型号带有升级证明或替代证明.6.不合格处理方式:物品不符合技术要求,无条件退换货;退换货产生的费用由供货方承担."} |
| 气缸 | MT4 - 160/40*1150 | 1.00 | 个 | {"型号":"MT4 - 160/40*1150","规格尺寸":"缸径:160mm;活塞杆:40mm;行程:1150mm","工作方式":"双作用拉杆式","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"涂层线","国内/国外":"国内","生产厂家":"不限","计量单位":"ITE","参照标准":"GB/T 32336-2015","备注":"技术要求:带中间耳轴,从****中心线距离XV=500mm.\n材质:缸筒:阳极氧化铝;缸盖:铝;活塞杆:镀硬铬刚;密封:丁腈橡胶、聚氨酯.\n工作压力:0.5~10bar.工作温度:-20~80℃\n使用寿命:大于730天.\n到货验收:产品有合格证明,产品完好无破损并符合上述技术要求.活塞杆活动运行顺畅.气密性良好.若物品不符合技术要求,无条件退换货;退换货产生的费用由供货方承担."} |
| 气缸 | MT4 - 160/40*850 | 1.00 | 个 | {"型号":"MT4 - 160/40*850","规格尺寸":"缸径:160mm;活塞杆:40mm;行程:850mm","工作方式":"双作用拉杆式","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"涂层线","国内/国外":"国内","生产厂家":"不限","计量单位":"ITE","参照标准":"GB/T 32336-2015","备注":"技术要求:带中间耳轴,从****中心线500mm.\n材质:缸筒:阳极氧化铝;缸盖:铝;活塞杆:镀硬铬刚;密封:丁腈橡胶、聚氨酯.\n工作压力:0.5~10bar.工作温度:-20~80℃\n使用寿命:大于730天.\n到货验收:产品有合格证明,产品完好无破损并符合上述技术要求.活塞杆活动运行顺畅.气密性良好.若物品不符合技术要求,无条件退换货;退换货产生的费用由供货方承担."} |
| 气缸 | P1D-BT200MS-0070 | 3.00 | 个 | {"型号":"P1D-BT200MS-0070","规格尺寸":"缸径:200mm;活塞杆:40mm;行程:70mm","工作方式":"双作用拉杆式","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"涂层线","国内/国外":"国内","生产厂家":"不限","计量单位":"ITE","参照标准":"GB/T 32336-2015","备注":"材质:缸筒:阳极氧化铝;缸盖:铝;活塞杆:不锈钢1Cr18Ni9MoZr;密封:丁腈橡胶、聚氨酯.\n工作压力:0.5~10bar.工作温度:-20~80℃\n使用寿命:大于730天.\n到货验收:产品有合格证明,产品完好无破损并符合上述技术要求.活塞杆活动运行顺畅.气密性良好.若物品不符合技术要求,无条件退换货;退换货产生的费用由供货方承担."} |
| 气缸 | DNC-80-150-PPV | 2.00 | 个 | {"型号":"DNC-80-150-PPV","规格尺寸":"缸径80mm,行程150mm","工作方式":"单杆双作用","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"轧机","国内/国外":"无要求","生产厂家":"无要求","计量单位":"ITE","参照标准":"GB/T 28781-2012","备注":"使用寿命365天,到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 电磁气缸 | SC80*25-S | 4.00 | 个 | {"型号":"SC80*25-S","规格尺寸":"缸径80mm,行程25mm,活塞杆直径25mm,接口尺寸PT3/8","工作方式":"电磁驱动双作用","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"倒角机","国内/国外":"国内","生产厂家":"无要求","计量单位":"ITE","参照标准":"GB/T 28781-2012","备注":"使用寿命365天,到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 气缸 | HYCJ63*50-50 | 4.00 | 个 | {"型号":"HYCJ63*50-50","规格尺寸":"缸径63mm,行程50mm,调整行程50mm,接口PT1/4","工作方式":"双作用","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"倒角机","国内/国外":"国内","生产厂家":"无要求","计量单位":"ITE","参照标准":"GB/T 28781-2012","备注":"使用寿命365天,到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 气缸 | CP96SDB63-80 | 6.00 | 个 | {"型号":"CP96SDB63-80","规格尺寸":"缸径63mm,行程80mm,活塞杆直径20mm,接口尺寸G3/8","工作方式":"双作用","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"厚剪机","国内/国外":"国内","生产厂家":"无要求","计量单位":"ITE","参照标准":"GB/T 28781-2012","备注":"使用寿命365天,到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 气缸 | 63/20*220 | 8.00 | 个 | {"型号":"63/20*220","规格尺寸":"行程:220mm;接口尺寸:G3/8;缸径:63mm;杆径;20mm","工作方式":"单杆双作用","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"空气","适用设备":"铝箔轧机","国内/国外":"国内","生产厂家":"无","计量单位":"ITE","参照标准":"GB/T 28781-2012","备注":"驱动方式;两端缓冲可调,侧向气口,缸体材质;铝合金,活塞杆材质;45#钢表面镀铬.使用寿命;365天.到货验收标准:1.包装完好,内部备件无破碎、损坏.2.型号,参数,等必须符合技术要求.3.升级型号的或替代型号的备件应带有升级或替代证明.4.若不符合技术要求或出现质量问题,则退换货,产生的费用由供货方承担."} |
| 气缸 | QGBI 100*220MT3 | 2.00 | 个 | {"型号":"QGBI 100*220MT3","规格尺寸":"缸径Φ100,杆径Φ25,行程220。","工作方式":"单杆双作用","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"铝箔轧机断箔刀","国内/国外":"国内","生产厂家":"无","计量单位":"ITE","参照标准":"GB/T 32336-2015","备注":"保证图纸中标注尺寸，其余尺寸按照样本制作，安装孔20mm。\n压力0.7MPa。\n附带S关节轴承接头：SB-4。\n使用寿命：不小于1年。\n验收标准:到货要带合格证,气缸表面不准有碰伤及裂纹,若达不到要求厂家要无条件退货或换货."} |
| 气缸 | RA8160M650D | 4.00 | 个 | {"型号":"RA8160M650D","规格尺寸":"160*650mm","工作方式":"双作用气缸","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"阿亨巴赫轧机","国内/国外":"国外","生产厂家":"诺冠","计量单位":"ITE","参照标准":"GB/T 23252-2009","备注":"验收：到货尺寸必须满足技术要求，对于不合格的进行退换货处理，所有产生费用由卖家承担。"} |
| 液压缸 | CDH2MT4/180/110/1000A3X/V1000mm | 1.00 | 个 | {"规格型号":"CDH2MT4/180/110/1000A3X/V1000mm","材质":"45钢","压力":"250bar","行程":"1000mm","活塞杆直径":"110mm","活塞直径":"180mm","密封件材质":"丁腈橡胶,聚氨酯,酚醛树脂","使用寿命":"730天","特殊要求":"两端可调式节流缓冲,缸杆镀铬处理","计量单位":"ITE","参照标准":"ISO 6022-2006"} |
| 油缸 | ATEY80*45*1150 | 3.00 | 个 | {"规格型号":"ATEY80*45*1150","行程":"650mm","活塞杆直径":"45mm","活塞直径":"80mm","所属设备名称":"混捏锅","设备型号":"4000L","国产/进口":"国产","计量单位":"PI"} |
| 夹具油缸 | D/d-L=50/31.5-36 | 2.00 | 个 | {"规格型号":"D/d-L=50/31.5-36","图号":"D/d-L=50/31.5-36","材质":"缸筒材质:机械构造用碳素钢（STK13C）活塞材质：机械构造用碳钢（s45C）表面镀铬","压力":"21MPa","行程":"36mm","活塞杆直径":"31.5mm","活塞直径":"50mm","密封件材质":"橡胶/合成树脂","接口尺寸":"M14*1.5mm","所属设备名称":"多功能天车","设备型号":"PTM32(25+25G28.5mA7-I","设备生产厂家":"中国有色（沈****公司","国产/进口":"国产","使用寿命":"730天","特殊要求":"无","计量单位":"ITE","参照标准":"JB/T 10205-2010","备注":"产品与技术要求不符，予以退换货处理。"} |
| 旋转气缸 | WGDTM80*240 | 1.00 | 个 | {"型号":"WGDTM80*240","气源压力":"0.3—0.5Mpa","作用形式":"双作用","计量单位":"ITE"} |
| 下接臂气缸 | GDCCB80*80-Y | 2.00 | 个 | {"型号":"GDCCB80*80-Y","气源压力":"0.3—0.5Mpa","作用形式":"双作用","计量单位":"ITE"} |
| 气缸 | GDC-CA50*60-Y | 2.00 | 个 | {"型号":"GDC-CA50*60-Y","气源压力":"0.4-1.2Mpa","作用形式":"双作用","计量单位":"ITE"} |
| 翻转顶紧气缸 | GDC-CA-80*60-Y | 2.00 | 个 | {"型号":"GDC-CA-80*60-Y","工作电压":"0","适用设备":"普通铝锭铸造机","国内/国外":"国内","生产厂家":"**重工","计量单位":"ITE"} |
| 摇摆气缸 | HYC80*175 | 2.00 | 个 | {"型号":"HYC80*175","工作电压":"0","适用设备":"普通铝锭铸造机","国内/国外":"国内","生产厂家":"**重工","计量单位":"ITE"} |
| 下料气缸 | QGB-ES63*150-L5 | 2.00 | 个 | {"型号":"QGB-ES63*150-L5","气源压力":"0.15-0.8MPa","作用形式":"双作用","公称直径":"63mm","计量单位":"ITE","参照标准":"GB/T23252-2015"} |
| 浇包气缸 | GDCN-CA-150*160-I | 2.00 | 个 | {"型号":"GDCN-CA-150*160-I","气源压力":"1.0-9BAR","作用形式":"双作用","公称直径":"150mm","特殊需求":"行程160mm;工作温度5-60℃;外壳材质：铝合金","计量单位":"ITE","参照标准":"GB/T23252-2015"} |
| 标准气缸 | SC40*150-S | 2.00 | 个 | {"型号":"SC40*150-S","规格尺寸":"缸径40mm，行程150mm","工作方式":"气动","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"太阳能边框自动线","国内/国外":"国内","生产厂家":"无要求","计量单位":"ITE","参照标准":"GB/T 23252-2009","备注":"本体是铝合金材质，工作形式：复动型，使用压力：0.15~1.0MPa,气管接口PT1/4，保证耐压力：1.5MPa，工作温度：-20°~70°，使用寿命大于1年，使用速度范围：30mm/s~800mm/s，缓冲形式：可调缓冲，缓冲行程：21mm，是否附磁石：附磁石，购买品牌不限制，只要能配合安装尺寸即可。到货产品如与技术要求不符实行退换货处理，由此产生的费用由厂家承担。"} |
| 迷你气缸 | MBL32*100-S-U | 2.00 | 个 | {"型号":"MBL32*100-S-U","规格尺寸":"缸径32mm，行程100mm","工作方式":"气动","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"太阳能边框自动线","国内/国外":"国内","生产厂家":"无要求","计量单位":"ITE","参照标准":"GB/T 23252-2009","备注":"本体是铝合金材质，工作形式：复动型，使用压力：0.15~1.0MPa,气管接口PT1/8，保证耐压力：1.5MPa，工作温度：-20°~70°，使用寿命大于1年，使用速度范围：30mm/s~800mm/s，缓冲形式：防撞垫，是否附磁石：附磁石，平尾型，购买品牌不限制，只要能配合安装尺寸即可。到货产品如与技术要求不符实行退换货处理，由此产生的费用由厂家承担。"} |
| 开门气缸 | GDC-CB-80*350-Y | 1.00 | 个 | {"型号":"GDC-CB-80*350-Y","气源压力":"1.0-9BAR","作用形式":"双作用","公称直径":"80mm","特殊需求":"行程350mm;工作温度5-60℃;外壳材质：铝合金","参照标准":"GB/T23252-2015"} |
| 气缸 | Φ125*450 | 1.00 | 个 | {"型号":"Φ125*450","规格尺寸":"Φ125*450","工作方式":"单杆双作用","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"高压空气","适用设备":"挤压机辅机","国内/国外":"国外","生产厂家":"欧玛福","参照标准":"JB/T 5923-2013"} |
| 气缸 | Φ125*215 | 1.00 | 个 | {"型号":"Φ125*215","规格尺寸":"缸径125mm,行程215mm","工作方式":"双作用式","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气","适用设备":"45MN燃气炉上棒台","国内/国外":"国内","生产厂家":"不指定","参照标准":"ISO 15552","备注":"带中部耳轴,外壳和活塞材质:铝合金,活塞杆材质:调质45#钢镀铬,密封材质:丁腈橡胶.\n工作压力0.1~1Mpa,工作温度0~80℃,使用寿命大于6个月.\n来货时必须有合格证,技术说明书.\n不合格品处理:对于验收检验不合格又不能使用的,限期进行退换货,由此产生的相关费用由供货方承担."} |
| 液压缸 | HSGΦ220*160-1250 | 2.00 | 个 | {"规格型号":"HSGΦ220*160-1250","图号":"无","材质":"45#钢","压力":"315bar","行程":"1250","活塞杆直径":"160mm","活塞直径":"220mm","密封件材质":"聚四氟乙烯;丁晴橡胶","接口尺寸":"DN32","所属设备名称":"200吨废料打包机","设备型号":"200T","设备生产厂家":"无","国产/进口":"国产","使用寿命":"730天","特殊要求":"无","参照标准":"JB/T 10205-2010","备注":"到货验收：液压缸尺寸必须满足上述技术要求，对于不合格的要求退换货处理，所有产生费用由卖方进行承担。"} |
| 气缸 | 63/16-50 | 4.00 | 个 | {"型号":"63/16-50","规格尺寸":"63/16-50","工作方式":"双作用式","输入信号":"无","输出信号":"无","工作电压":"0","适用介质":"压缩空气（工作压力：0.7MPa）","适用设备":"双机架冷轧机电磁加热","国内/国外":"国内","生产厂家":"不指定","参照标准":"ISO 21287","备注":"材质:缸体：铝合金；缸杆：45#钢。工作压力：0.7MPa；寿命2年以上。不限定品牌；外形尺寸、安装尺寸要求与技术要求相符；外形轮廓、形状细节不要求与图片完全一致。到货验收：不满足技术要求，退换货处理；退换货产生的费用由供货方承担。"} |
| 倾翻臂液压缸 | PNXLY | 2.00 | 个 | {"规格型号":"PNXLY","图号":"无","材质":"碳钢,活塞杆,缸筒表面镀铬","压力":"20MPa","行程":"762mm","活塞杆直径":"45mm","活塞直径":"63.5mm","密封件材质":"氟橡胶,丁腈橡胶,聚四氟乙烯","接口尺寸":"活塞杆螺纹1-7/8-12","所属设备名称":"铸造机","设备型号":"800S","设备生产厂家":"美国瓦格斯塔夫","国产/进口":"进口","使用寿命":"730天","特殊要求":"介质:液压油","参照标准":"JB/T 10205-2010","备注":"缸径152.4mm,最小缩回长度1254mm.验收:到货不合格供应商必须无条件退货或换货处理,所产生的费用由供货方承担."} |
| 三联体 | DN25 | 3.00 | 个 | {"型号":"DN25","工作电压":"0"} |
| 可调节消声器 | M10 | 20.00 | 个 | {"规格型号":"M10","序列号":"无","阀门规格":"通用型气动电磁阀","国内/国外":"国内","生产厂家":"国产","特殊需求":"无","参照标准":"JB/T 7352-2010","备注":"应用到国产电磁阀(BM520），黄铜材质，接口尺寸：外螺纹公称直径10mm。使用寿命1年以上，验收标准：与技术要求不符，退换货处理。"} |
| 粗轧用十字轴式万向联结轴 | 570*ф150 mm | 6.00 | 件 | {"规格型号":"570*ф150 mm","图号":"****1900","材质":"传动轴叉头材质ZG35CrMo,中间连接管材质 480QZ,十字包材质20CrMnTi","所属设备":"热粗轧机粗轧工作辊轴承座使用","设备生产厂家":"德国SMS","国产/进口":"不指定","特殊要求":"5500Nm,平衡等级G16(ISO 1940),工作夹角＜25°","参照标准":"GB/T 28700-2012","备注":"1.材质：传动轴叉头材质ZG35CrMo,中间连接管材质 480QZ，十字包材质20CrMnTi。\n2.公称扭矩：5500Nm，平衡等级G16（ISO 1940）,工作夹角＜25°。\n3.包装完好无破损，无锈蚀，如果供应商供货与提报计划不符，要求供应商调换货，如果因质量问题造成损失由供货商负责。"} |
| 旋转辊道万向传动轴 | 1650*285 | 2.00 | 根 | {"规格型号":"1650*285","图号":"****8757","材质":"铸钢","所属设备":"热粗轧机旋转辊道","设备生产厂家":"唐****公司","国产/进口":"国产","特殊要求":"最大扭矩：60knm 最小扭矩：40knm"} |
| 液压螺母 | NO-50668-2 | 1.00 | 件 | {"规格型号":"NO-50668-2","图号":"****1167","材质":"外壳铝合金","所属设备名称":"重卷线","设备型号":"HCBBCJ-03","设备生产厂家":"******公司","国产/进口":"国产","使用寿命":"730天","特殊要求":"无","参照标准":"MT/T 913-2002"} |
| 液压螺母 | M56*4 | 2.00 | 个 | 规格型号 M56*4 图号 无 材质 42CrMo4v 所属设备名称 3#拉矫 设备型号 TLL-2100 设备生产厂家 FATA 国产/进口 国产 使用寿命 730天 特殊要求 最高工作压力：2275bar，最大压紧力：783.73KN，最大液压面积：3444.56mm2，尺寸：φ105mm(外径)*75(高度)，行程：8mm，螺纹尺寸：M56*4，此备件为非标产品，需定制，请供应商根据车间提供的样品进行加工制作 计量单位 ITE 参照标准 MT/T 913-2002 备注 到货后不合格,由供货商无条件退货、换货,由此产生的费用,由供货商承担 |
| 气动执行器 | DN150 | 4.00 | 个 | 型号 DN150 气源压力 0.2~0.8MPa 作用形式 单作用 公称直径 150mm 安装孔径 M12 回转角度 90° 电磁阀电源 24V 控制功能 气动 辅助机构 电磁阀及限位开关 输出扭矩 24~13022Nm 生产厂家 国产 特殊需求 使用寿命≥1460天 计量单位 ITE 参照标准 GB/T 32215-2015 备注 1.缸体主要材质：铝合金 2.该气缸采购不指定供货厂家,满足现场使用即可. 3.使用寿命:正常使用不低于4年. 4.验收标准:产品有合格证明,产品完好无破损并符合上述技术要求. 5.若产品升级,升级型号或替代型号带有升级或替代证明. 6.随货物附带合格证明或能证明产品质量的文件，外表无破损，要求执行器动作灵活无卡顿现象，复核主要安装尺寸需能满足上述要求，现场安装测试正常。 7.不合格处理方式：物品不符合技术要求或不适应现场使用,无条件退换货；退换货产生的费用,由供货方承担. |
换一批
换一批