物品名称 规格型号 数量 单位 描述
| 1型非金属嵌件六角锁紧螺母 | {"直径":"M10","材质":"304不锈钢","表面处理":"无","性能等级":"A2-70, 锁紧塑圈材质尼龙","特殊要求":"螺母拥有自锁功能","使用寿命":"365天","参照标准":"GB/T 889.1","备注":"产品完好无破损，符合上述技术要求，附带合格证。不合格品处理标准：如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 8600.00 | 个 | |
| 螺母 | {"直径":"M45","高度":"34.4~36.9mm","材质":"Q235钢","表面处理":"无","性能等级":"不低于4.8级","使用寿命":"3650天","参照标准":"GB/T 41-2016","备注":"来货必须附有产品材质证明（合格证），来货验收达不到技术要求，供货商应无条件给予退换货处理。（退换货产生的一切费用由供货商承担）"} | 50.00 | 个 | |
| 全丝内六角螺丝 | {"直径":"M33","长度":"140mm","图号":"无","螺纹长度":"140mm","材质":"45#碳钢","表面处理":"发黑热处理","性能等级":"12.9级","使用寿命":"60天","参照标准":"GB/T 16938-2008","备注":"产品完好无破损并符合上述技术要求，附带合格证。不合格品处理标准：如果到货物资不符合技术要求，予以换货处理，产生的费用由供货商负责。"} | 50.00 | 个 | |
| 六角法兰面螺栓 | {"直径":"M8","长度":"30","图号":"/","螺纹长度":"30mm","材质":"304不锈钢","表面处理":"无","性能等级":"A2-70","使用寿命":"1095天","特殊要求":"无","参照标准":"GB/T 5789","备注":"产品完好无破损，符合上述技术要求，附带合格证。不合格品处理标准：如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 50.00 | 个 | |
| 全丝杆 | {"直径":"M10","长度":"806","材质":"Q235","表面处理":"镀锌","使用寿命":"1095天","性能等级":"8.8","特殊要求":"无","参照标准":"GB/T 3098.1","备注":"产品完好无破损，符合上述技术要求，附带合格证。不合格品处理标准：如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 50.00 | 个 | |
| 全丝杆 | {"直径":"M10","长度":"1006","材质":"Q235","表面处理":"镀锌","使用寿命":"1095天","性能等级":"4.8","特殊要求":"无","参照标准":"GB/T 3098.1","备注":"产品完好无破损，符合上述技术要求，附带合格证。不合格品处理标准：如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 3950.00 | 个 | |
| 全丝杆 | {"直径":"M10","长度":"1206mm","材质":"Q235","表面处理":"镀锌","使用寿命":"1095天","性能等级":"4.8","特殊要求":"无","参照标准":"GB/T 3098.1","备注":"产品完好无破损，符合上述技术要求，附带合格证。不合格品处理标准：如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 50.00 | 个 | |
| 全丝杆 | {"直径":"M10","长度":"1406","材质":"Q235","表面处理":"镀锌","使用寿命":"1095天","性能等级":"4.8","特殊要求":"无","参照标准":"GB/T 3098.1","备注":"产品完好无破损，符合上述技术要求，附带合格证。不合格品处理标准：如到货不符合技术要求，由供应商无条件进行更换、退货。"} | 50.00 | 个 | |
| 不锈钢细牙盖型螺母 | {"直径":"M27","图号":"0","高度":"43mm","材质":"不锈钢304","表面处理":"不经处理","性能等级":"A2-70","特殊要求":"型号：M27*1.5*43mm","使用寿命":"365天","参照标准":"GB/T 3098.15-2014","备注":"不锈钢细牙盖型螺母: M27*1.5*43mm；\n验收标准: 丝扣均匀、无缺丝、断丝现象，到货后不符合要求，供应商应无条件退换货 ，所产生费用由供应商提供"} | 50.00 | 个 | |
| 十字槽沉头螺丝 | {"直径":"M6","长度":"10mm","图号":"无","螺纹长度":"10mm","材质":"不锈钢304","表面处理":"酸洗，光亮","性能等级":"A2-70","使用寿命":"730天","参照标准":"GB/T 3098.6-2014","备注":"外观：不能有毛刺，不得有裂纹和明显缺陷\n设备紧固件，到货物资达不到技术要求，供货厂家无偿退换货，退换货所产生的费用由厂家自行承担。"} | 1900.00 | 个 | |
| 锁紧螺母 | {"直径":"M10","材质":"低碳合金钢","表面处理":"无","性能等级":"8.8级","特殊要求":"螺母拥有自锁功能","使用寿命":"300天","参照标准":"GB/T 6184-2000","备注":"自锁材质：尼龙；若到货与技术要求不符或存在质量问题，厂家无条件进行退换货，产生的费用由厂家提供。"} | 50.00 | 个 | |
| 内六角螺栓 | {"直径":"M36","长度":"260mm","图号":"M36*260","螺纹长度":"100mm","材质":"低碳合金钢","表面处理":"表面光洁无刺、表面有防锈处理","性能等级":"8.8级","使用寿命":"730天","参照标准":"GB/T 5783-2016","备注":"1、验收标准：无断丝，外观良好，无锈蚀痕迹，无错丝等缺陷，到货时附带出厂合格证。\n2、不合格处理：如到货后不符合技术要求，供货商应无条件给予退货或换货。"} | 50.00 | 个 | |
| 不锈钢法盘三角螺栓 | {"直径":"M8","长度":"46","图号":"无","螺纹长度":"22.5±0.5mm","材质":"不锈钢304","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"360天","参照标准":"GB/T 3098.6-2014","备注":"特性:总长:53.2±1mm,丝长:22.5±0.5mm，丝杆：23.5±0.5mm\n使用设备名称：日常检修使用（国产）\n验收标准：无断丝，外观良好，无锈蚀痕迹，无错丝等缺陷，到货时附带出厂合格证。\n不合格处理：如到货后不符合技术要求，供货商应无条件给予退货或换货。"} | 500.00 | 个 | |
| 内六角圆柱头螺钉 | {"直径":"M20","长度":"55mm","材质":"35CrMoA","表面处理":"发黑","性能等级":"12.9","使用寿命":"≥365天","参照标准":"GB/T 70.1-2008","备注":"1、螺纹长度为55mm。\n2、外观良好，无断丝，无错丝，无锈蚀痕迹等缺陷，到货时附带出厂合格证。\n3、如到货验收不符合技术要求，供货商无条件给予退换货处理，产生的费用由供货商承担。"} | 50.00 | 根 | |
| 马鞍卡 | {"规格型号":"Φ20","材质":"Q235","使用寿命":"1000天","特殊要求":"表面热镀锌","参照标准":"GB/T 90.3-2010","备注":"表面无锌渣光滑平整，不符合要求的退换,产生的费用由厂家承担"} | 59700.00 | 个 | |
| 高强外六角螺杆 | {"直径":"M10","长度":"65","图号":"01","螺纹长度":"30mm","材质":"45#钢","表面处理":"氧化发黑,","性能等级":"碳钢8.8级","使用寿命":"365天","参照标准":"GB/T 5782-2016","备注":"规格:M10*65,有丝长:M10*30mm,无丝处长:Φ10*35mm,外六方厚:7mm, 对边宽:17mm.到货螺杆如与上述技术要求不符，供货商给予退货或调换"} | 500.00 | 个 | |
| 高强外六角螺杆 | {"直径":"M10","长度":"55","图号":"02","螺纹长度":"30mm","材质":"45#钢","表面处理":"氧化发黑,","性能等级":"碳钢8.8级","使用寿命":"365天","参照标准":"GB/T 5782-2016","备注":"规格:M10*55,有丝长:M10*30mm,无丝处长:Φ10*25mm,外六方厚:7mm, 对边宽:17mm.到货螺杆如与上述技术要求不符，供货商给予退货或调换"} | 400.00 | 个 | |
| 开槽沉头螺钉 | {"直径":"M6mm","长度":"25mm","材质":"25Cr2MoV","表面处理":"无","性能等级":"无","使用寿命":"2190天","参照标准":"GB/T 68-2016","备注":"螺距P=1.0mm;零部件供货时提供到货清单+合格证；合金等特殊材质件需提供材质检测报告单；如有特殊使用要求或说明则应在合格证上标明或附带说明书等资料。到货与本技术要求不符，厂家无条件免费退换货。"} | 50.00 | 个 | |
| 不锈钢螺栓 | {"直径":"M16","长度":"50mm","图号":"无","螺纹长度":"50mm","材质":"316L不锈钢","表面处理":"无","性能等级":"A4-80","使用寿命":"1095天","参照标准":"GB/T 5783-2016","备注":"到货与技术附件不符,予以退/换货."} | 1188.00 | 个 | |
| 不锈钢螺栓 | {"直径":"M20","长度":"130","图号":"无","螺纹长度":"52mm","材质":"304不锈钢","表面处理":"无需处理","性能等级":"A2-70","使用寿命":"90天","参照标准":"GB/T 3098.6-2014"} | 50.00 | 个 | |
| 镀锌自攻丝 | {"直径":"M3.9","长度":"40","材质":"4.8级碳钢（渗碳钢）","表面处理":"平头十字槽，表面镀蓝锌，做钝化防腐处理。","性能等级":"4.8","使用寿命":"3650天","参照标准":"GB/T 15856.2-2002"} | 12000.00 | 个 | |
| 镀锌自攻丝 | {"直径":"M3.9","长度":"50","材质":"4.8级碳钢（渗碳钢）","表面处理":"平头十字槽口，表面镀锌，钝化防腐处理","性能等级":"4.8级","使用寿命":"3650天","参照标准":"GB/T 15856.2-2002"} | 1980.00 | 个 | |
| 镀锌自攻丝 | {"直径":"M3.9","长度":"60","材质":"4.8级碳钢（渗碳钢）","表面处理":"平头十字槽口，表面镀锌，钝化防腐处理","性能等级":"4.8级","使用寿命":"3650天","参照标准":"GB/T 15856.2-2002"} | 24900.00 | 个 | |
| 自攻钉 | {"直径":"M3.5(±0.2mm)","长度":"60(±2mm)","图号":"无","螺纹长度":"40-60mm","材质":"碳钢","表面处理":"镀锌","性能等级":"3.6","使用寿命":"365天","特殊要求":"无","参照标准":"GB/T 846-2017"} | 7900.00 | 个 | |
| 内六角螺丝 | {"直径":"M10mm","长度":"110mm","图号":"M10*110","螺纹长度":"33±2mm","材质":"45#碳钢","表面处理":"发黑热处理","性能等级":"8.8级","使用寿命":"60天","参照标准":"GB/T 16938-2008","备注":"产品完好无破损并符合上述技术要求，附带合格证。不合格品处理标准：如果到货物资不符合技术要求，予以换货处理，产生的费用由供货商负责。"} | 100.00 | 个 | |
| U型卡 | {"直径":"M6","长度":"89mm","图号":"无","螺纹长度":"28mm","材质":"Q235A","表面处理":"镀锌","性能等级":"无","使用寿命":"3650天","参照标准":"GB/T 3098.1-2010","备注":"带配套螺丝"} | 50.00 | 套 | |
| 内六角螺栓 | {"直径":"M6","长度":"50mm","材质":"碳钢","表面处理":"无","性能等级":"12","使用寿命":"365天","参照标准":"GB/T 5782-2016"} | 400.00 | 个 | |
| 双头螺丝 | {"直径":"M16","长度":"160","图号":"1","螺纹长度":"45mm","材质":"46碳钢","表面处理":"无","性能等级":"8.8","使用寿命":"365天","特殊要求":"无","参照标准":"GB/T 16938-2008"} | 40.00 | 个 | |
| 内六角螺丝 | {"直径":"M3","长度":"40","材质":"碳钢","表面处理":"中碳钢并热处理","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 70.1-2008"} | 50.00 | 个 | |
| 不锈钢外六角螺丝 | {"直径":"M18","长度":"90mm(不含外六角）","图号":"M18*90","螺纹长度":"90mm","材质":"304不锈钢","表面处理":"不经处理","性能等级":"A2-70","使用寿命":"180天","参照标准":"GB/T 3098.6-2014"} | 50.00 | 个 | |
| 圆柱头焊钉 | {"直径":"M16","长度":"100mm","材质":"ML15","表面处理":"无锈蚀、氧化皮、毛刺","性能等级":"/","使用寿命":"9125天","参照标准":"GB/T 10433-2002","备注":"对来货验收不合格的，供货商负责将货物无条件给予更换至验收合格为止，否则予以退货。（退换货产生的一切费用由供货商承担）"} | 16860.00 | 个 | |
| 十字沉头螺丝杆 | {"直径":"M4","长度":"35mm","图号":"无","螺纹长度":"35mm","材质":"碳钢镀锌","表面处理":"镀锌","性能等级":"8.8","使用寿命":"1825天","参照标准":"GB/T 819.2-2016"} | 1000.00 | 个 | |
| 十字沉头自攻螺丝 | {"直径":"M4","长度":"40mm","材质":"4.8级碳钢","表面处理":"镀蓝锌处理，做钝化防锈处理","性能等级":"4.8","使用寿命":"1825天","参照标准":"GB/T 15856.2-2002"} | 55500.00 | 个 | |
| 十字沉头自攻螺丝 | {"直径":"M4","长度":"14mm","材质":"4.8级碳钢","表面处理":"镀蓝锌处理，做钝化防锈处理","性能等级":"4.8","使用寿命":"1825天","参照标准":"GB/T 15856.2-2002"} | 464000.00 | 个 | |
| 十字沉头自攻螺丝 | {"直径":"M4","长度":"10mm","材质":"4.8级碳钢","表面处理":"镀蓝锌处理，做钝化防锈处理","性能等级":"4.8","使用寿命":"1825天","参照标准":"GB/T 15856.2-2002"} | 50.00 | 个 | |
| 十字沉头自攻螺丝 | {"直径":"M4","长度":"50mm","材质":"4.8级碳钢","表面处理":"镀蓝锌处理，做钝化防锈处理","性能等级":"4.8","使用寿命":"1825天","参照标准":"GB/T 15856.2-2002"} | 21000.00 | 个 | |
| 化学螺栓 | {"直径":"M12","长度":"160mm","图号":"M12*160","螺纹长度":"160mm","材质":"Q2235、化学胶管：树脂、固化剂、石英颗粒","表面处理":"无","性能等级":"4.8级","使用寿命":"1825天","参照标准":"GB/T 22795-2008","备注":"来货验收不合格的，供货商负责将货物无条件给予更换至验收合格为止，否则予以退货。（退换货产生的一切费用由供货商承担）"} | 50.00 | 套 | |
| 非金属嵌件六角锁紧螺母 | {"直径":"M8","材质":"SUS316+尼龙","表面处理":"无","性能等级":"8级","特殊要求":"无","使用寿命":"1825天","参照标准":"GB/T 889.1、GB/T 193、GB/T 3098.2、GB/T 3098.9","备注":"规格：GB/T 889.1 M8\n来料必须在底部面标记（A4-80）标记（表示SUS316材质，机械性能等级8级）；\n不合格品处理：若到货与技术要求不符或存在质量问题，供应商需进行退换货处理，由此产生的费用由供应商承担；\n引用标准，不标记发布版本，以最新版本或最新替代标准为准；\n申请原因：丹麦INQ2188海上平台项目装配需要。"} | 114588.00 | 件 | |
| 膨胀螺丝 | {"规格型号":"M8*100*1.0","直径":"8mm","长度":"100mm","强度等级":"4.8","表面处理":"防腐蚀","材质要求":"表面镀锌 碳钢","配套附件":"螺帽 垫片","参照标准":"GB/T 22795-2008","备注":"一次性消耗品 高抗拉 防生锈 防腐蚀"} | 5030.00 | 个 | |
| 外六角螺母 | {"直径":"M5mm","高度":"4.8mm","材质":"Q235","表面处理":"镀锌","性能等级":"c级","使用寿命":"365天","参照标准":"GB/T 41-2016","备注":"要求包装完整无破损、规格一致。使用寿命至少为1年。"} | 300.00 | 个 | |
| 不锈钢挂件 | {"规格型号":"70*50*5","材质":"不锈钢304制成的钢体","使用寿命":"21900天","特殊要求":"尺寸符合规定，表面光滑无锈迹","参照标准":"GB/T 32839-2016","备注":"不符合技术要求，退换货处理，所产生的费用由供货商承担。"} | 2400.00 | 个 | |
| 不锈钢挂件 | {"规格型号":"80*50*5","材质":"不锈钢304制成的钢体","使用寿命":"21900天","特殊要求":"尺寸符合规定，表面光滑无锈迹","参照标准":"GB/T 32839-2016","备注":"不符合技术要求，退换货处理，所产生的费用由供货商承担。"} | 7000.00 | 个 | |
| 不锈钢挂件 | {"规格型号":"90*50*5","材质":"不锈钢304制成的钢体","使用寿命":"21900天","特殊要求":"尺寸符合规定，表面光滑无锈迹","参照标准":"GB/T 32839-2016","备注":"不符合技术要求，退换货处理，所产生的费用由供货商承担。"} | 6100.00 | 个 | |
| 挑件 | {"规格型号":"70*50*5","材质":"不锈钢304制成的钢体","使用寿命":"21900天","特殊要求":"尺寸符合规定，表面光滑无锈迹","参照标准":"GB/T 32839-2016","备注":"不符合技术要求，退换货处理，所产生的费用由供货商承担。"} | 1600.00 | 个 | |
| 挑件 | {"规格型号":"80*50*5","材质":"不锈钢304制成的钢体","使用寿命":"21900天","特殊要求":"尺寸符合规定，表面光滑无锈迹","参照标准":"GB/T 32839-2016","备注":"不符合技术要求，退换货处理，所产生的费用由供货商承担。"} | 5200.00 | 个 | |
| 挑件 | {"规格型号":"90*50*5","材质":"不锈钢304制成的钢体","使用寿命":"21900天","特殊要求":"尺寸符合规定，表面光滑无锈迹","参照标准":"GB/T 32839-2016","备注":"不符合技术要求，退换货处理，所产生的费用由供货商承担。"} | 4600.00 | 个 | |
| 螺栓 | {"直径":"M5mm","长度":"60mm","材质":"Q235","表面处理":"镀锌","性能等级":"4.8","使用寿命":"365天","参照标准":"GB/T 35480-2017","备注":"产品包装完整、无破损 规格型号应与要求一致. 使用寿命至少为1年."} | 400.00 | 个 | |
| F30直钉 | {"长度":"30±1mm","直径":"1.51±0.01mm","表面处理":"涂胶均匀","材质":"Q195","允许偏差":"长度30±1mm,直径1.51±0.01mm","特殊要求":"外观光洁无锈蚀,无伤痕,排列整齐,5000支/盒","参照标准":"GB/T 701-2008"} | 6200.00 | 盒 | |
| 50钢排钉 | {"长度":"50mm","直径":"2.2mm","表面处理":"镀锌","材质":"Q195","允许偏差":"长度±2mm,直径±0.15mm","特殊要求":"400个/盒","参照标准":"GB/T 27704-2011"} | 10500.00 | 盒 | |
| 双头螺栓 | {"直径":"M42","长度":"420mm","图号":"无","螺纹长度":"85+60mm","材质":"铬钼钢调质处理","表面处理":"发黑","性能等级":"12.9","使用寿命":"365天","特殊要求":"加工尺寸见图片","参照标准":"GB/T 3098.1-2010"} | 50.00 | 个 | |
| 双头螺栓 | {"直径":"M42","长度":"540mm","图号":"无","螺纹长度":"85+60mm","材质":"铬钼钢调质处理","表面处理":"发黑","性能等级":"12.9","使用寿命":"365天","特殊要求":"加工尺寸见图片","参照标准":"GB/T 3098.1-2010"} | 50.00 | 个 | |
| 双头螺栓 | {"直径":"M42","长度":"660mm","图号":"无","螺纹长度":"85+60mm","材质":"铬钼钢调质处理","表面处理":"发黑","性能等级":"12.9","使用寿命":"365天","特殊要求":"加工尺寸见图片","参照标准":"GB/T 3098.1-2010"} | 50.00 | 个 | |
| 尼龙平垫圈 | {"直径":"M8（内径8.4-8.62mm，外径15.57-16mm）","厚度":"1.6±0.2mm","材质":"尼龙（PA66）","表面处理":"无","性能等级":"DIN 34815 tabelle 2","使用寿命":"1825天","参照标准":"DIN 34815","备注":"材质，尺寸，性能符合DIN 34815标准\n（平垫规格 8 16 DIN34815）(垫片尺寸：内径8.4-8.62mm，外径15.57-16mm，厚度1.6±0.2mm)；\n不合格品处理：若到货与技术要求不符或存在质量问题，供应商需进行退换货处理；\n引用标准，不标记发布版本，以最新版本或最新替代标准为准；\n申请原因：丹麦INQ2188海上平台项目使用"} | 61300.00 | 件 | |
| 自攻自钻螺钉 | {"直径":"6.3mm","长度":"150mm","材质":"CH1022A","性能等级":"4.8级","表面处理":"电镀","特殊要求":"无","参照标准":"GB/T 15856.4-2002","备注":"使用年限:正常环境下大于5年.\n质量要求:电镀,外观完好,平整光洁,无毛刺,镀层光亮,丝扣均匀.断丝,偏心等不合格率＜5%."} | 3128.00 | 个 | |
| 自攻自钻螺钉 | {"直径":"6.3mm","长度":"100mm","材质":"CH1022A","性能等级":"4.8级","表面处理":"电镀","特殊要求":"无","参照标准":"GB/T 15856.4-2002","备注":"使用年限:正常环境下大于5年.\n质量要求:电镀,外观完好,平整光洁,无毛刺,镀层光亮,丝扣均匀.断丝,偏心等不合格率＜5%."} | 32000.00 | 个 | |
| 内六角圆头螺钉 | {"直径":"M30","长度":"310mm","材质":"碳钢","表面处理":"发黑除锈处理","性能等级":"≥8.8级","使用寿命":"≥90天","参照标准":"GB/T 70.1-2008","备注":"内六角圆头螺钉\\M30\\310mm\\碳钢\\发黑除锈处理\\≥8.8级\\使用寿命≥90天\\GB/T70.1-2008"} | 50.00 | 个 | |
| 半丝内六角螺丝 | {"直径":"M8mm","长度":"50mm","材质":"碳钢","表面处理":"发黑处理","性能等级":"12.9级","使用寿命":"不低于180天","参照标准":"GB/T 16938-2008"} | 1100.00 | 个 | |
| 高强螺栓 | {"直径":"M24mm","长度":"80mm","图号":"M24*80","螺纹长度":"80mm","材质":"螺栓20MnTiB,螺母45#,垫圈45#","表面处理":"发黑处理","性能等级":"10.9s","使用寿命":"9125天","参照标准":"GB/T 1228-2006"} | 100.00 | 套 | |
| 六角头螺栓 | {"直径":"M30","长度":"80mm","图号":"无","螺纹长度":"80mm","材质":"45","表面处理":"碳黑","性能等级":"8.8","使用寿命":"2190天","参照标准":"GB/T 5783-2016","备注":"图纸上“GB/T5783-2000”被标注在“图号”栏内，经查工标网，已被“GB/T 5783-2016”替代。"} | 300.00 | 个 | |
| 螺栓 | {"直径":"M10","长度":"有效长度15mm","图号":"-","螺纹长度":"15mm","材质":"45","表面处理":"光滑","性能等级":"标准件","使用寿命":"≥365天","参照标准":"GB/T 5783-2016"} | 600.00 | 个 | |
| 不锈钢平垫 | {"直径":"M12","厚度":"1.5mm","材质":"316L","表面处理":"不需要防腐处理","性能等级":"无","使用寿命":"730天","参照标准":"GB/T 97.3-2000","备注":"到货产品必须符合技术要求,不符合技术要求厂家必须无条件退换货物."} | 28740.00 | 个 | |
| 外六角螺栓 | {"直径":"M10","长度":"45","图号":"无","螺纹长度":"45mm","材质":"碳钢","表面处理":"碳黑","性能等级":"8.8","使用寿命":"1095天","参照标准":"GB/T 5780-2016"} | 1000.00 | 个 | |
| 双头螺栓 | {"直径":"M18","长度":"100","图号":"无","螺纹长度":"35mm","材质":"碳钢","表面处理":"碳黑","性能等级":"8.8","使用寿命":"1095天","特殊要求":"无","参照标准":"GB/T 3098.1-2010"} | 50.00 | 个 | |
| 高强度双头螺栓 | {"直径":"M14","长度":"60","图号":"无","螺纹长度":"25mm","材质":"碳钢","表面处理":"碳黑","性能等级":"8.8","使用寿命":"1095天","特殊要求":"无","参照标准":"GB/T 3098.1-2010"} | 23.00 | 个 | |
| T型螺栓 | {"直径":"M48","长度":"340mm","图号":"T133-2","螺纹长度":"150mm","材质":"5CrNiMo","表面处理":"螺杆和螺母必须经过锻造，T型头必须为墩头锻造成形","性能等级":"强度≥8.8级","使用寿命":"90天","特殊要求":"严格按照图纸尺寸要求加工，螺杆、螺母和垫片可采用标准件。T形螺杆可采用螺杆和T型头独立方案。 安装使用按装配图进行，球面凹凸垫片必须配对使用，不可单独使用，凹凸面必须相接触放置","参照标准":"GB/T 41-2016、GB/T 97.1-2002、GB/T 37-1988","备注":"T型螺栓\\M48*340mm\\T133-2\\螺纹长150mm\\5CrNiMo\\螺杆和螺母必须经过锻造，T型头必须为墩头锻造成形\\强度≥8.8级\\使用寿命90天\\严格按照图纸尺寸要求加工，螺杆、螺母和垫片可采用标准件。T形螺杆可采用螺杆和T型头独立方案。 安装使用按装配图进行，球面凹凸垫片必须配对使用，不可单独使用，凹凸面必须相接触放置\\GB/T 41-2016、GB/T 97.1-2002、GB/T 37-1988"} | 50.00 | 个 | |
| T型螺栓 | {"直径":"M48","长度":"310mm","图号":"T132-2","螺纹长度":"150mm","材质":"5CrNiMo","表面处理":"螺杆和螺母必须经过锻造，T型头必须为墩头锻造成形","性能等级":"强度≥8.8级","使用寿命":"90天","特殊要求":"严格按照图纸要求尺寸加工，螺杆、螺母和垫片可采用标准件，T形螺杆可采用螺杆和T型头独立方案。安装使用按装配图进行，球面凹凸垫片必须配对使用，不可单独使用，凹凸面必须相接触放置。","参照标准":"GB/T 41-2016、GB/T 97.1-2002、GB/T 37-1988","备注":"T型螺栓\\M48*310mm\\T132-2\\螺纹长150mm\\5CrNiMo\\螺杆和螺母必须经过锻造，T型头必须为墩头锻造成形\\强度≥8.8级\\使用寿命90天\\严格按照图纸尺寸要求加工，螺杆、螺母和垫片可采用标准件。T形螺杆可采用螺杆和T型头独立方案。 安装使用按装配图进行，球面凹凸垫片必须配对使用，不可单独使用，凹凸面必须相接触放置\\GB/T 41-2016、GB/T 97.1-2002、GB/T 37-1988"} | 50.00 | 个 | |
| 镀锌丝杆 | {"直径":"M0.014","长度":"3000mm","材质":"铁镀锌","表面处理":"镀锌","使用寿命":"730天","性能等级":"4.8","特殊要求":"无","参照标准":"GB/T 15389-1994"} | 50.00 | 根 | |
| 螺栓 | {"直径":"M14mm","长度":"25mm","图号":"无","螺纹长度":"25mm","材质":"45#钢","表面处理":"发黑","性能等级":"8.8","使用寿命":"≥365天","参照标准":"GB/T 5782-2016","备注":"如到货与技术要求不符,由供应商无条件进行退,换货处理"} | 3915.00 | 个 | |
| 双头螺栓 | {"直径":"M22","长度":"120mm","图号":"无","螺纹长度":"45mm","材质":"45#钢","表面处理":"表面热处理","性能等级":"8.8级","使用寿命":"365天","特殊要求":"无","参照标准":"GB/T 5782-2016"} | 376.00 | 个 | |
| 双头螺栓 | {"直径":"M10","长度":"100mm","图号":"无","螺纹长度":"45mm","材质":"45#钢","表面处理":"表面经热处理","性能等级":"8.8级","使用寿命":"365天天","特殊要求":"无","参照标准":"GB/T 5782-2016"} | 50.00 | 个 | |
| 内六角螺丝 | {"直径":"M5","长度":"80","材质":"不锈钢304","表面处理":"无","性能等级":"A2-70","使用寿命":"180天","参照标准":"GB/T 3098.6-2014","备注":"强度等级:8.8级\n螺纹为全丝"} | 1400.00 | 个 | |
| 不锈钢盖型螺帽 | {"直径":"M10","图号":"0","高度":"1cm","材质":"不锈钢304","表面处理":"酸洗,光亮","性能等级":"A2-70","特殊要求":"丝扣均匀,无缺丝,断丝现象.","使用寿命":"720天","参照标准":"GB/T 3098.15-2014"} | 4000.00 | 个 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"1000mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm"} | 1315.00 | 支 | |
| 马鞍扣 | {"直径":"M28mm*31mm","材质":"Q235B","表面处理":"无","性能等级":"无","特殊要求":"无","使用寿命":"3650天","参照标准":"GB/T 700-2006","备注":"适用于YX820型彩瓦防水垫（防水胶垫厚度≥1.0mm）；上层彩板厚度≥0.4mm，漆膜厚度≥20μm，拉伸强度≥260N/㎡。"} | 139840.00 | 个 | |
| 自攻钉防水帽 | {"规格型号":"六棱形内径5.5mm,外形圆直径≥15mm","材质":"聚乙烯塑料","使用寿命":"2920天","特殊要求":"无","参照标准":"GB/T 11115-2009","备注":"钢结构安装彩瓦燕尾钉专用防水、防锈、装饰用。"} | ****000.00 | 个 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"1100mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求"} | 1024.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"1200mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求"} | 3716.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"1400mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求"} | 2992.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"1350mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求"} | 9358.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"1650mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求"} | 12172.00 | 支 | |
| 内六角螺丝 | {"直径":"M10","长度":"80mm","图号":"无","螺纹长度":"80mm","材质":"碳钢","表面处理":"发黑处理","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 3098-2010"} | 1000.00 | 个 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"2100mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求，若到货产品达不到技术要求予以退换货处理。（退换货产生的一切费用由供货商承担）"} | 1100.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"2300mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求，若到货产品达不到技术要求予以退换货处理。（退换货产生的一切费用由供货商承担）"} | 96.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"2400mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求，若到货产品达不到技术要求予以退换货处理。（退换货产生的一切费用由供货商承担）"} | 536.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"2450mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求，若到货产品达不到技术要求予以退换货处理。（退换货产生的一切费用由供货商承担）"} | 792.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"2550mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求，若到货产品达不到技术要求予以退换货处理。（退换货产生的一切费用由供货商承担）"} | 1256.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"2600","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求，若到货产品达不到技术要求予以退换货处理。（退换货产生的一切费用由供货商承担）"} | 824.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"2800mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求，若到货产品达不到技术要求予以退换货处理。（退换货产生的一切费用由供货商承担）"} | 2080.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"3050mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求，若到货产品达不到技术要求予以退换货处理。（退换货产生的一切费用由供货商承担）"} | 1224.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"500mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求，若到货产品达不到技术要求予以退换货处理。（退换货产生的一切费用由供货商承担）"} | 250.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"600mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求，若到货产品达不到技术要求予以退换货处理。（退换货产生的一切费用由供货商承担）"} | 612.00 | 支 | |
| 热镀锌拉条 | {"圆钢直径":"ф12mm","圆钢长度":"900mm","材质":"Q235B","镀锌量":"180g","表面处理":"热镀锌","参照标准":"GB/T 702-2017","备注":"两端切丝各长100mm，使用寿命25年。热镀锌层应符合GB/T 13912相关要求，若到货产品达不到技术要求予以退换货处理。（退换货产生的一切费用由供货商承担）"} | 912.00 | 支 | |
| 十字沉头螺丝杆 | {"直径":"M4","长度":"20mm","图号":"无","螺纹长度":"20mm","材质":"碳钢","表面处理":"镀锌","性能等级":"8.8","使用寿命":"1825天","参照标准":"GB/T 819.2-2016"} | 50.00 | 个 | |
| 螺母 | {"直径":"M18mm","高度":"14mm","材质":"25Cr2MoV","表面处理":"无","性能等级":"无","使用寿命":"2190天","参照标准":"GB/T 6170-2015"} | 100.00 | 个 | |
| 不锈钢内六角顶丝 | {"直径":"M8","长度":"15mm","图号":"0","螺纹长度":"15mm","材质":"304不锈钢","表面处理":"0","性能等级":"A2-70","使用寿命":"≥90天","特殊要求":"螺纹为全丝。 3、耐酸、碱，韧性高。1、如配件到货质量与技术要求不符，退换货产生的费用由供货方承担。 2、因****公司经****公司相关规定进行处罚。","参照标准":"GB/T 3280-2015"} | 700.00 | 个 | |
| 内六角螺丝 | {"直径":"M14","长度":"30","图号":"M14*30","螺纹长度":"30","材质":"45#钢","表面处理":"光洁、无毛刺","性能等级":"12.9 级","使用寿命":"180天","参照标准":"GB/T 70.1-2008"} | 100.00 | 个 | |
| 不锈钢螺母 | {"直径":"M5mm","高度":"4mm","材质":"304不锈钢","表面处理":"酸洗，光亮","性能等级":"A2-70","使用寿命":"730天","参照标准":"GB/T 3098.15-2014"} | 6000.00 | 个 | |
| 吊环 | {"直径":"M20","长度":"34mm","材质":"45钢","表面处理":"整体锻造,并经正火处理和清除氧化皮","性能等级":"12.9","使用寿命":"90天","参照标准":"GB/T 27696-2011"} | 60.00 | 个 | |
| 不锈钢沉头螺丝 | {"直径":"M6mm","长度":"16mm","图号":"无","螺纹长度":"16mm","材质":"304不锈钢","表面处理":"酸洗，光亮","性能等级":"A2-70","使用寿命":"730天","参照标准":"GB/T 3098.6-2014"} | 250.00 | 个 | |
| 外六角螺栓 | {"直径":"M30","长度":"220mm","图号":"无","螺纹长度":"85mm","材质":"中碳钢调质处理","表面处理":"发黑","性能等级":"8.8级","使用寿命":"365天","参照标准":"GB/T 5782-2016"} | 50.00 | 个 | |
| 沉头自攻钉 | {"直径":"M3.5","长度":"40mm","材质":"8.8级碳钢（渗碳钢）","表面处理":"发黑","性能等级":"8.8","使用寿命":"3650天","参照标准":"GB/T 846-2017"} | 50.00 | 个 | |
| 内六角螺丝 | {"直径":"M10","长度":"35MM","材质":"碳钢","表面处理":"中碳钢并热处理","性能等级":"12.9","使用寿命":"365天","参照标准":"GB/T 16938-2008"} | 600.00 | 个 | |
| 吊环螺钉 | {"直径":"M10","长度":"20mm","材质":"45#钢","表面处理":"镀锌钝化，电镀锌后应立即进行去氢处理。","性能等级":"12.9级","使用寿命":"60天","参照标准":"GB/T 27696-2011","备注":"1.吊环螺钉 必须经整体锻造。锻件应进行正火处理，并清除氧化皮。成品的晶粒度不应低于5级，锻件不应有过烧、裂纹缺陷。\n2.来货物资若与技术要求不符和有质量问题,厂家无条件退换货处理,产生费用由供货商承担."} | 30.00 | 个 | |
| 外六角螺丝 | {"直径":"M14","长度":"50","图号":"无","螺纹长度":"50mm","材质":"低碳合金钢并淬火、回火处理","表面处理":"发黑","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 5781-2016"} | 195.00 | 个 | |
| 不锈钢螺丝 | {"直径":"M14","长度":"50mm","图号":"0","螺纹长度":"50mm","材质":"不锈钢304","表面处理":"0","性能等级":"A2-70","使用寿命":"1095天","参照标准":"GB/T 3098.6-2014","备注":"不产品使用寿命3年,不锈钢螺丝/14mm/50mm/不锈钢304/A2-70/1095天/GB/T3098.6-2014"} | 373.00 | 个 | |
| 高强螺栓 | {"直径":"M24","长度":"85mm","图号":"M24x85","螺纹长度":"85mm","材质":"螺栓MnTiB/螺母45#/垫圈45#","表面处理":"配M24平垫,弹簧垫","性能等级":"10.9s","使用寿命":"9125天","参照标准":"GB/T 16938-2008","备注":"本产品使用寿命25年,高强螺栓,材质为:螺栓MnTiB/螺母45#/垫圈45#/24mm/85mm/10.9s/GB/T16938-2008"} | 20.00 | 个 | |
| 螺母 | {"直径":"M42mm","高度":"25mm","材质":"Q235","表面处理":"无","性能等级":"4.8级","使用寿命":"9125天","参照标准":"GB/T 41-2016","备注":"本品使用寿命25年,螺母/42M/Q235/0/4.8级/0/ITE个/GB/T 41-2016"} | 50.00 | 个 | |
| 内六角螺丝 | {"直径":"M64","长度":"620","材质":"中碳钢经热处理淬火并回火","表面处理":"发蓝","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 70.1-2008"} | 50.00 | 个 | |
| 内六角螺丝 | {"直径":"M24","长度":"110","材质":"45#碳钢","表面处理":"发蓝","性能等级":"12.9","使用寿命":"365天","参照标准":"GB/T 3098.1-2010"} | 278.00 | 个 | |
| 不锈钢螺栓 | {"直径":"M8","长度":"25.5mm","图号":"无","螺纹长度":"20mm","材质":"316L","表面处理":"无","性能等级":"标准件","使用寿命":"1095天","参照标准":"GB/T 5783-2016"} | 44300.00 | 个 | |
| 吊环 | {"直径":"M36","长度":"螺距：4mm","材质":"25#钢","表面处理":"吊环螺钉整体锻造，并经正火处理和清除氧化皮","性能等级":"载荷：4T","使用寿命":"180天","参照标准":"GB/T 27696-2011"} | 4.00 | 个 | |
| 不锈钢双头螺栓 | {"直径":"M20","长度":"200","图号":"无","螺纹长度":"50mm","材质":"304不锈钢","表面处理":"不经处理","性能等级":"304不锈钢","使用寿命":"1460天","特殊要求":"无","参照标准":"GB/T 3106-2016"} | 100.00 | 个 | |
| 不锈钢双头螺栓 | {"直径":"M18","长度":"100mm","图号":"无","螺纹长度":"36mm","材质":"不锈钢304","表面处理":"不经处理","性能等级":"A2-50","使用寿命":"730天","特殊要求":"两端螺纹等长","参照标准":"GB/T 3106-2016"} | 50.00 | 个 | |
| 高压双头螺栓 | {"直径":"M24","长度":"110mm","图号":"无","螺纹长度":"53mm","材质":"不锈钢316L","表面处理":"不经处理","性能等级":"A4-70","使用寿命":"1095天","特殊要求":"两端螺纹等长","参照标准":"GB/T 3106-2016"} | 50.00 | 个 | |
| 双头螺栓 | {"直径":"M14","长度":"240mm","图号":"无","螺纹长度":"50mm","材质":"不锈钢304","表面处理":"不经处理","性能等级":"A2-50","使用寿命":"730天","特殊要求":"两端螺纹等长","参照标准":"GB/T 3106-2016"} | 50.00 | 个 | |
| 外六角螺栓 | {"直径":"M27","长度":"160mm","图号":"无","螺纹长度":"55mm","材质":"碳钢","表面处理":"发黑处理","性能等级":"4.8级","使用寿命":"730天","参照标准":"GB/T 5782-2016"} | 200.00 | 个 | |
| 螺栓 | {"直径":"M4","长度":"16","材质":"碳钢","表面处理":"镀锌","性能等级":"4.8","使用寿命":"365天","参照标准":"GB/T 16938-2008","备注":"带帽,平垫和弹簧垫"} | 50.00 | 套 | |
| 化学螺栓 | {"直径":"M16","长度":"180mm","图号":"16Mx180mm","螺纹长度":"180mm","材质":"Q235,化学胶管:树脂,固化剂,石英颗粒","表面处理":"无","性能等级":"4.8级","使用寿命":"1825天","参照标准":"GB/T 22795-2008","备注":"本品使用寿命5年以上,化学螺栓,16mm/180mm/16Mx180mm/180mm/Q235,化学胶管:树脂,固化剂,石英颗粒/4.8级/SET套/GB/T 22795-2008"} | 3500.00 | 套 | |
| 化学螺栓 | {"直径":"M24","长度":"300mm","图号":"300mmx24m","螺纹长度":"300mm","材质":"Q235,化学胶管:树脂,固化剂,石英颗粒","表面处理":"无","性能等级":"4.8级","使用寿命":"730天","参照标准":"GB/T 22795-2008","备注":"本品使用寿命:2年/化学螺栓/24mm/300mm/24Mx300mm/4.8级/Q235,化学胶管:树脂,固化剂,石英颗粒/SET套/GB/T 22795-2008"} | 624.00 | 套 | |
| 内六角紧定螺丝 | {"直径":"M10","长度":"15mm","材质":"碳钢","表面处理":"发黑热处理","性能等级":"8.8","使用寿命":"360天","参照标准":"GB/T 16938-2008"} | 50.00 | 个 | |
| 内六角螺栓 | {"直径":"M5","长度":"40mm","材质":"碳钢","表面处理":"发黑热处理","性能等级":"8.8","使用寿命":"360天","参照标准":"GB/T 16938-2008"} | 1533.00 | 个 | |
| 全丝外六角螺栓 | {"直径":"M16","长度":"90mm","图号":"M16*90/8.8级","螺纹长度":"100mm","材质":"45#钢","表面处理":"氧化发黑","性能等级":"8.8级","使用寿命":"365天","参照标准":"GB/T 5783-2016","备注":"M16*90/8.8级/氧化发黑/验收标准：到货产品若不符合技术要求，予以退换货处理。"} | 1196.00 | 个 | |
| 自锁式外六角法兰螺母 | {"直径":"M24","高度":"19mm","材质":"45#碳钢","表面处理":"镀锌","性能等级":"8.8级","使用寿命":"365天","参照标准":"GB/T 6177.1-2000","备注":"1、使用寿命：反击破用，平均寿命1年，\n2、验货标准：如不符合要求应予以退换货。"} | 50.00 | 个 | |
| 内六角螺丝 | {"直径":"M64","长度":"350mm","材质":"碳钢","表面处理":"要求表面光洁、无刺","性能等级":"10.9","使用寿命":"180天","参照标准":"GB/T 70.1-2000"} | 50.00 | 个 | |
| 内六角螺栓 | {"直径":"M30","长度":"120mm","材质":"合金钢淬火并回火","表面处理":"要求表面光洁、无刺","性能等级":"12.9","使用寿命":"180天","参照标准":"GB/T 70.1-2000","备注":"螺距3.5"} | 98.00 | 根 | |
| 内六角螺丝 | {"直径":"M48","长度":"200mm","材质":"碳钢","表面处理":"要求表面光洁、无刺","性能等级":"8.8","使用寿命":"180天","参照标准":"GB/T 70.1-2000"} | 40.00 | 个 | |
| 外六角螺栓 | {"直径":"M30","长度":"240","图号":"M30*240","螺纹长度":"82mm","材质":"低碳合金钢并淬火、回火处理","表面处理":"发黑","性能等级":"8.8","使用寿命":"180天","参照标准":"GB/T 5781-2016"} | 50.00 | 个 | |
| 止退螺帽 | {"直径":"M20","材质":"碳钢","表面处理":"镀锌钝化","性能等级":"5级","特殊要求":"防松材质：尼龙","使用寿命":"180天","参照标准":"GB/T 3098.9-2020"} | 50.00 | 个 | |
| 不锈钢双头螺栓 | {"直径":"M24","长度":"330mm","图号":"无","螺纹长度":"60mm","材质":"316L","表面处理":"酸洗、光亮","性能等级":"A4-50","使用寿命":"1460天","特殊要求":"两端螺纹等长","参照标准":"GB/T 3106-2016"} | 50.00 | 条 | |
| 双头螺栓 | {"直径":"M30","长度":"90mm","图号":"无","螺纹长度":"90mm","材质":"不锈钢316L","表面处理":"酸洗，光亮","性能等级":"A4-50","使用寿命":"365天","特殊要求":"两头全部带相同材质螺帽","参照标准":"GB/T 3106-2016"} | 50.00 | 套 | |
| 不锈钢双头螺栓 | {"直径":"M30","长度":"80mm","图号":"无","螺纹长度":"80mm","材质":"不锈钢316L","表面处理":"酸洗、光亮","性能等级":"A4-50","使用寿命":"365天","特殊要求":"两头全部带相同材质螺帽","参照标准":"GB/T 3106-2016"} | 50.00 | 套 | |
| 吊环螺钉 | {"直径":"M30","长度":"45mm","材质":"45#钢","表面处理":"镀锌","性能等级":"12.9级","使用寿命":"50天","参照标准":"GB 825-1988"} | 108.00 | 个 | |
| 内六角螺丝 | {"直径":"M8","长度":"58mm","图号":"M8*50/12.9级","螺纹长度":"50mm","材质":"45#钢","表面处理":"淬火及回火","性能等级":"12.9","使用寿命":"365天","参照标准":"GB/T 70.1-2008","备注":"验收标准：产品完好无破损并符合上诉技术要求，附带合格证。处理方式：如所送的物品达不到以上技术要求，生产厂家必须无条件退货，并再次送货至合格为止。"} | 860.00 | 个 | |
| 内六角螺丝 | {"直径":"M36","长度":"360mm","材质":"碳钢","表面处理":"发黑热处理","性能等级":"12.9","使用寿命":"365天","参照标准":"GB/T 70.1-2000","备注":"丝杆长:360mm,丝长::145mm,螺距:4"} | 70.00 | 个 | |
| 沉头螺丝 | {"直径":"M16","长度":"65mm","图号":"无","螺纹长度":"65mm","材质":"发黑碳钢","表面处理":"发黑处理","性能等级":"8.8","使用寿命":"730天","参照标准":"GB/T 70.3-2008","备注":"使用寿命:2年"} | 4300.00 | 个 | |
| 高强度双头螺栓 | {"直径":"M16","长度":"100","图号":"M16*100/8.8级","螺纹长度":"65","材质":"碳钢","表面处理":"无","性能等级":"8.8","使用寿命":"720天","特殊要求":"-","参照标准":"GB/T 3098.1-2010","备注":"如不符合技术要求供应商予以无条件退换处理。"} | 50.00 | 个 | |
| 钢结构用大六角头高强度螺栓连接副 | {"直径":"M22","长度":"85mm","图号":"无","螺纹长度":"45mm","材质":"螺栓20MnTiB、螺母45#、垫圈45#","表面处理":"外观应清洁无裂纹、破损、油垢、锈蚀、氧化皮.毛刺等现象","性能等级":"10.9S级","使用寿命":"9125天","参照标准":"GB/T 1228-2006、GB/T 1229-2006、GB/T 1230-2006","备注":"一套：1个螺栓、1个螺母、2个垫圈。螺栓GB/T 1228-2006、螺母GB/T 1229-2006、垫圈GB/T 1230-2006"} | 50.00 | 套 | |
| 钢结构用大六角头高强度螺栓连接副 | {"直径":"M20","长度":"65mm","图号":"无","螺纹长度":"40mm","材质":"螺栓20MnTiB、螺母45#、垫圈45#","表面处理":"外观应清洁无裂纹、破损、油垢、锈蚀、氧化皮.毛刺等现象。","性能等级":"10.9S级","使用寿命":"9125天","参照标准":"GB/T 1228-2006、GB/T 1229-2006、GB/T 1230-2006","备注":"一套：1个螺栓、1个螺母、2个垫圈。螺栓GB/T 1228-2006、螺母GB/T 1229-2006、垫圈GB/T 1230-2006"} | 50.00 | 套 | |
| 钢结构用大六角头高强度螺栓连接副 | {"直径":"M24","长度":"60mm","图号":"无","螺纹长度":"45mm","材质":"螺栓20MnTiB、螺母45#、垫圈45#","表面处理":"外观应清洁无裂纹、破损、油垢、锈蚀、氧化皮.毛刺等现象。","性能等级":"10.9S级","使用寿命":"9125天","参照标准":"GB/T 1228-2006、GB/T 1229-2006、GB/T 1230-2006","备注":"一套：1个螺栓、1个螺母、2个垫圈。螺栓GB/T 1228-2006、螺母GB/T 1229-2006、垫圈GB/T 1230-2006"} | 50.00 | 套 | |
| 钢结构用大六角头高强度螺栓连接副 | {"直径":"M30","长度":"110mm","图号":"无","螺纹长度":"60mm","材质":"螺栓20MnTiB、螺母45#、垫圈45#","表面处理":"外观应清洁无裂纹、破损、油垢、锈蚀、氧化皮.毛刺等现象。","性能等级":"10.9S级","使用寿命":"9125天","参照标准":"GB/T 1228-2006、GB/T 1229-2006、GB/T 1230-2006","备注":"一套：1个螺栓、1个螺母、2个垫圈。螺栓GB/T 1228-2006、螺母GB/T 1229-2006、垫圈GB/T 1230-2006"} | 408.00 | 套 | |
| 扁头螺栓 | {"直径":"M36","长度":"215mm","图号":"无","螺纹长度":"120mm","材质":"中碳钢","表面处理":"发黑处理","性能等级":"8.8","使用寿命":"365天","特殊要求":"无","参照标准":"GB/T 3098.1-2010","备注":"附带产品合格证及材质检测报告，若到货物资与技术要求不符时，厂家无偿进行换货。"} | 50.00 | 根 | |
| 自攻自钻螺钉 | {"直径":"6.3mm","长度":"125mm","材质":"CH1022A","性能等级":"4.8级","表面处理":"电镀,镀层光亮","特殊要求":"无","参照标准":"GB/T 15856.4-2002","备注":"本品使用寿命:正常情况下大于5年.\n质量要求:电镀,外观完好,平整,光洁,无毛刺,镀层光亮,丝扣均匀,断丝,偏心等不合格率＜5%"} | 7000.00 | 个 | |
| 不锈钢螺帽 | {"直径":"M36","高度":"31","材质":"不锈钢304","表面处理":"无","性能等级":"不锈钢304","使用寿命":"＞1460天","参照标准":"GB/T 3098.15-2014"} | 50.00 | 个 | |
| 不锈钢螺母 | {"直径":"M6","高度":"5.7mm","材质":"不锈钢304","表面处理":"酸洗，光亮","性能等级":"A2-70","使用寿命":"365天","参照标准":"GB/T 3098.15-2014"} | 1700.00 | 个 | |
| 不锈钢内膨胀螺丝 | {"直径":"M10","长度":"100mm","图号":"无","螺纹长度":"30mm","材质":"304不锈钢","表面处理":"无","性能等级":"8.8","使用寿命":"365天","特殊要求":"无","参照标准":"GB/T 22795-2008","备注":"到货验收:包装完好,外观完好无损,带有合格证.如所送到物品不符合技术要求或质量不合格,供货商必须无条件退换货,由此产生的费用由供货商负责."} | 2100.00 | 套 | |
| 内六角沉头螺丝 | {"直径":"M12","长度":"100","图号":"无","螺纹长度":"50","材质":"45#钢","表面处理":"淬火发黑","性能等级":"8.8级","使用寿命":"1825天","参照标准":"GB/T5781-2016"} | 4600.00 | 个 | |
| 不锈钢螺母 | {"直径":"M8","高度":"7.9mm","材质":"不锈钢","表面处理":"不经表面处理","性能等级":"5级","使用寿命":"90天","参照标准":"GB/T 858-1988","备注":"对于验收检验不合格又不能使用的,限期进行退换货,由此产生的相关费用由供货方承担.对于验收不合格的供应商,要求其制订整改计划,并对整改效果进行验证;对整改不符合要求的供应商,取消其供货资格."} | 2804.00 | 个 | |
| 不锈钢螺母 | {"直径":"M27","高度":"22.6~24.7mm","材质":"不锈钢316L","表面处理":"无","性能等级":"8.8","使用寿命":"1140天","参照标准":"GB/T 41-2016","备注":"不合格产品处理要求:如不符合技术要求,要求进行退,换货处理"} | 50.00 | 个 | |
| 外六角螺丝 | {"直径":"M10","长度":"50mm","图号":"M20*50","螺纹长度":"32~33mm","材质":"45#碳钢","表面处理":"无","性能等级":"8.8","使用寿命":"360天","参照标准":"GB/T 5781-2000","备注":"不符合技术要求予以退换货处理"} | 50.00 | 个 | |
| 内六角螺丝 | {"直径":"M16","长度":"35mm","图号":"M16*35","螺纹长度":"31~33mm","材质":"碳钢","表面处理":"无","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 5781-2000","备注":"不符合技术要求供应商无条件退换货,所产生费用全部由供应商承担"} | 50.00 | 个 | |
| 外六角螺栓 | {"直径":"M24","长度":"100mm","图号":"M24*100","螺纹长度":"48~51mm","材质":"不锈钢","表面处理":"无","性能等级":"4.8","使用寿命":"365天","参照标准":"GB/T 5781-2000","备注":"如不符合技术要求供应商予以无条件退换货"} | 50.00 | 个 | |
| 双头螺栓 | {"直径":"M16","长度":"60mm","图号":"M16*60","螺纹长度":"17~19,21~23mm","材质":"20Cr1Mo1VTiB","表面处理":"无","性能等级":"8.8","使用寿命":"1460天","特殊要求":"接触介质:蒸汽,介质压力:14MPa,零部件工作最高温度550℃","参照标准":"GB/T 897-1988","备注":"如不符合技术要求供应商予以无条件退换货"} | 50.00 | 个 | |
| 外六角不锈钢螺栓 | {"直径":"M20","长度":"50mm","图号":"M20*50","螺纹长度":"40~42mm","材质":"304不锈钢","表面处理":"无","性能等级":"4.8级","使用寿命":"365天","参照标准":"GB/T 3098-6-2014","备注":"如不符合技术要求供应商予以无条件退换货处理"} | 50.00 | 个 | |
| 高压双头螺栓 | {"直径":"M24","长度":"110mm","图号":"无","螺纹长度":"每头螺纹长度:40mm","材质":"45#钢","表面处理":"发黑","性能等级":"8.8","使用寿命":"730天","特殊要求":"带M24螺帽2个;带配套平垫2个","参照标准":"GB/T 901-1988","备注":"验收标准:到货需带合格证,表面应无损伤,如到货与技术要求不符厂家无条件进行退、换货。"} | 840.00 | 套 | |
| 自锁螺母 | {"直径":"M30","材质":"35Cr","表面处理":"发黑","性能等级":"10级","特殊要求":"螺纹M30*2.0","使用寿命":"1460天","参照标准":"GB/T 6171-2016","备注":"嵌件材质:尼龙"} | 50.00 | 个 | |
| 高压双头螺栓 | {"直径":"M16","长度":"60mm","图号":"无","螺纹长度":"25mm","材质":"45#钢","表面处理":"发黑","性能等级":"8.8级","使用寿命":"365天","特殊要求":"无","参照标准":"GB/T 901-1988"} | 50.00 | 个 | |
| 高强螺栓 | {"直径":"M22","长度":"75mm","图号":"无","螺纹长度":"40mm","材质":"螺栓:20MnTiB;螺母:45#;垫圈:45#","表面处理":"发黑","性能等级":"10.9级","使用寿命":"730天","参照标准":"GB/T 1228-2006","备注":"1、带螺母M22:1个;平垫:2个"} | 290.00 | 套 | |
| 不锈钢外六角螺栓 | {"直径":"M16","长度":"90mm","图号":"无","螺纹长度":"90mm","材质":"304不锈钢","表面处理":"不经处理","性能等级":"A2-70","使用寿命":"730天","参照标准":"GBT 5783-2016"} | 50.00 | 个 | |
| 不锈钢双头螺栓 | {"直径":"M24","长度":"100mm","图号":"无","螺纹长度":"40mm","材质":"316L","表面处理":"不经处理","性能等级":"316L","使用寿命":"1460天","特殊要求":"两端螺纹等长","参照标准":"GB/T 3106-2016"} | 50.00 | 个 | |
| 全丝内六角螺栓 | {"直径":"M6","长度":"80","材质":"碳钢","表面处理":"发黑热处理","性能等级":"12.9","使用寿命":"90天","参照标准":"GB/T 16938-2008"} | 20.00 | 个 | |
| 不锈钢内六角螺栓 | {"直径":"M14","长度":"50mm","图号":"无","螺纹长度":"50mm","材质":"不锈钢304","表面处理":"不经处理","性能等级":"不锈钢304","使用寿命":"1460天","参照标准":"GB/T 3106-2016"} | 50.00 | 个 | |
| 不锈钢螺帽 | {"直径":"M14","高度":"11mm","材质":"不锈钢316L","表面处理":"酸洗，光亮","性能等级":"A4-50","使用寿命":"365天","参照标准":"GB/T 41-2016"} | 200.00 | 个 | |
| 镀锌螺帽 | {"直径":"M20","高度":"18mm","材质":"Q235","表面处理":"热镀锌","性能等级":"4.8级","使用寿命":"730天","参照标准":"GB/T 41-2016"} | 1600.00 | 个 | |
| 不锈钢螺母 | {"直径":"M42","高度":"18mm","材质":"316L","表面处理":"不经处理","性能等级":"316L","使用寿命":"1460天","参照标准":"GB/T 6170-2015"} | 50.00 | 个 | |
| 内六角顶丝 | {"直径":"M10","长度":"20MM","材质":"碳钢","表面处理":"中碳钢并热处理","性能等级":"12.9","使用寿命":"180天","参照标准":"GB/T 16938-2008"} | 370.00 | 个 | |
| 内六角顶丝 | {"直径":"M6","长度":"10MM","材质":"35#碳钢","表面处理":"中碳钢并热处理","性能等级":"8.8","使用寿命":"180天","参照标准":"GB/T 16938-2008"} | 1950.00 | 个 | |
| 内六角螺丝 | {"直径":"M14","长度":"50MM","材质":"45#碳钢","表面处理":"中碳钢并热处理","性能等级":"12.9","使用寿命":"180天","参照标准":"GB/T 16938-2008"} | 260.00 | 个 | |
| 内六角螺丝 | {"直径":"M5","长度":"10MM","材质":"碳钢","表面处理":"中碳钢并热处理","性能等级":"8.8","使用寿命":"180天","参照标准":"GB/T 16938-2008"} | 300.00 | 个 | |
| 平键 | {"型号":"10*56","宽度":"10mm","高度":"8mm","长度":"56mm","材质":"316L","使用寿命":"≥1460天","参照标准":"GB/T 20878-2007"} | 50.00 | 个 | |
| 内六角螺丝 | {"直径":"M22","长度":"50MM","材质":"45#钢","表面处理":"中碳钢并热处理","性能等级":"12.9","使用寿命":"180天","参照标准":"GB/T 16938-2008"} | 80.00 | 个 | |
| 外六角螺栓 | {"直径":"M10mm","长度":"26mm","图号":"8.8","螺纹长度":"20","材质":"碳钢","表面处理":"发黑处理","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 5782-2016"} | 50.00 | 个 | |
| 内六角螺丝 | {"直径":"M22","长度":"80MM","材质":"45#钢","表面处理":"中碳钢并热处理","性能等级":"12.9","使用寿命":"180天","参照标准":"GB/T 16938-2008"} | 50.00 | 个 | |
| 内六角螺丝 | {"直径":"M30","长度":"150MM","材质":"冷镦和挤压用碳钢","表面处理":"氧化处理","性能等级":"12.9","使用寿命":"180天","参照标准":"GB/T 16938-2008"} | 122.00 | 个 | |
| 螺栓 | {"直径":"M10","长度":"70mm","图号":"无","螺纹长度":"30mm","材质":"碳钢","表面处理":"热镀锌","性能等级":"强度等级4.8级","使用寿命":"720天","参照标准":"GB/T 5780-2016"} | 50.00 | 个 | |
| 内六角螺栓 | {"直径":"M12","长度":"67mm","图号":"8.8","螺纹长度":"55mm","材质":"35#碳钢","表面处理":"表面发黑处理","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 70.1-2008","备注":"使存在与技术要求不符时,供货商应无条件给予更换或退货."} | 50.00 | 个 | |
| 外卡簧 | {"规格型号":"Ф20","材质":"65Mn弹簧钢","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 894-2017"} | 50.00 | 个 | |
| 不锈钢螺栓 | {"直径":"M8","长度":"30mm","图号":"无","螺纹长度":"30mm","材质":"316L不锈钢","表面处理":"无","性能等级":"A4-80","使用寿命":"1095天","参照标准":"GB/T 3098.6-2014","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} | 500.00 | 个 | |
| 内六角螺丝 | {"直径":"M12","长度":"80mm","图号":"无","螺纹长度":"80mm","材质":"45H碳钢","表面处理":"无","性能等级":"12.9级","使用寿命":"365天","参照标准":"GB/T 3098.6-2014","备注":"1.外观良好,无断丝、错丝.\n2.到货验收不符合技术要求,退换货处理,产生的费用由供应商承担."} | 300.00 | 个 | |
| 不锈钢外六角螺栓 | {"直径":"M12mm","长度":"100mm","图号":"无","螺纹长度":"100mm","材质":"不锈钢304","表面处理":"因材质为不锈钢，所以没有表面处理。","性能等级":"A2-70","使用寿命":"≥365天","参照标准":"GBT 5783-2016","备注":"验收标准:到货应附带合格证及材质检测报告.到货表面应光滑无裂纹铸造缺陷.产品出现质量问题，现场安装尺寸不符厂家要及时无条件更换或退货，若未达到使用寿命供货厂家必须给予赔付，所产生费用由供货商承担，****公司经济损失的，按照公司相关规定进行处罚。"} | 245.00 | 个 | |
| 全丝内六角螺丝 | {"直径":"M8","长度":"35mm","图号":"无","螺纹长度":"35mm","材质":"合金钢","表面处理":"无","性能等级":"12.9级","使用寿命":"365天","参照标准":"GB/T 3098.6-2014","备注":"1.外观良好,无断丝、错丝;\n2.到货后验收不符合技术要求,必须退换货,产生的费用由供应商承担."} | 900.00 | 个 | |
| 全丝加强内六角螺丝 | {"直径":"M16","长度":"60mm","图号":"无","螺纹长度":"60mm","材质":"45H碳钢","表面处理":"无","性能等级":"12.9级","使用寿命":"365天","参照标准":"GB/T 3098.6-2014","备注":"1.外观良好,无断丝、错丝.\n2.到货验收不符合技术要求,必须退换货,产生的费用由供应商承担."} | 460.00 | 个 | |
| 不锈钢螺栓 | {"直径":"M16","长度":"70mm","图号":"无","螺纹长度":"70mm","材质":"不锈钢304","表面处理":"无","性能等级":"A2-70","使用寿命":"365天","参照标准":"GB/T 3098.6-2014","备注":"1.外观良好,无断丝、错丝\n2.到货后验收不符合技术要求,必须退换货处理,产生的费用由供应商承担。"} | 810.00 | 个 | |
| 内六角螺丝 | {"直径":"M20","长度":"40mm","材质":"碳钢","性能等级":"8.8","使用寿命":"365天"} | 100.00 | 个 | |
| 内六角螺栓 | {"直径":"M4","长度":"10mm","螺纹长度":"10mm","材质":"碳钢","性能等级":"8.8","使用寿命":"365天"} | 3800.00 | 个 | |
| 全丝内六角螺丝 | {"直径":"M12","长度":"60mm","螺纹长度":"60mm","材质":"45钢","表面处理":"发黑处理","性能等级":"12.9级","使用寿命":"730天","参照标准":"GB/T 70.1-2008"} | 330.00 | 个 | |
| 全丝内六角螺栓 | {"直径":"M6","长度":"60mm","螺纹长度":"60mm","材质":"45钢","表面处理":"表面发黑处理","性能等级":"12.9级","使用寿命":"90天","参照标准":"GBT70.1-2008"} | 50.00 | 个 | |
| 外卡簧 | {"规格型号":"Ф65","材质":"65Mn弹簧钢","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 894-2017","备注":"到货验收:包装完好,外观完好无损,带有合格证.如所送到物品不符合技术要求或质量不合格,供货商必须无条件退换货,由此产生的费用由供货商负责."} | 10.00 | 个 | |
| 外卡簧 | {"规格型号":"Ф10","材质":"65Mn弹簧钢","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 894-2017","备注":"到货验收:包装完好,外观完好无损,带有合格证.如所送到物品不符合技术要求或质量不合格,供货商必须无条件退换货,由此产生的费用由供货商负责."} | 50.00 | 个 | |
| 外卡簧 | {"规格型号":"Ф18","材质":"65Mn弹簧钢","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 894-2017","备注":"到货验收:包装完好,外观完好无损,带有合格证.如所送到物品不符合技术要求或质量不合格,供货商必须无条件退换货,由此产生的费用由供货商负责."} | 200.00 | 个 | |
| 外卡簧 | {"规格型号":"Ф15","材质":"65Mn弹簧钢","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 894-2017","备注":"到货验收:包装完好,外观完好无损,带有合格证.如所送到物品不符合技术要求或质量不合格,供货商必须无条件退换货,由此产生的费用由供货商负责."} | 50.00 | 个 | |
| 单头螺栓 | {"直径":"M27","长度":"125mm","螺纹长度":"65mm","材质":"碳钢","性能等级":"8.8","使用寿命":"90天"} | 360.00 | 根 | |
| 不锈钢双头螺栓 | {"直径":"M27","长度":"140mm","螺纹长度":"80mm","材质":"316L","性能等级":"8.8","使用寿命":"90天"} | 50.00 | 根 | |
| 沉头螺丝 | {"直径":"M20","长度":"80mm","螺纹长度":"50mm","材质":"45钢","表面处理":"发黑处理","性能等级":"8.8级","使用寿命":"1095天","参照标准":"GB/T 819.1-2016"} | 1000.00 | 个 | |
| 双头螺栓 | {"直径":"M18","长度":"230mm","图号":"无","螺纹长度":">65mm","材质":"中碳钢","表面处理":"热处理(淬火、回火)","性能等级":"10.9级","使用寿命":"180天","参照标准":"GB/T 5780-2000、GB/T 5781-2000、GB/T 5782-2000、GB/T 5783-2000","备注":"配2个螺帽及2个弹簧垫"} | 50.00 | 套 | |
| 螺母(MMD) | {"直径":"M24","材质":"碳钢","性能等级":"10.9"} | 50.00 | 个 | |
| 螺栓(MMD) | {"直径":"M24","长度":"105mm","螺纹长度":"105mm","材质":"碳钢"} | 50.00 | 个 | |
| 膨胀管卡 | {"规格型号":"M8/DN15","直径":"8mm","长度":"175mm","强度等级":"4.8","表面处理":"热镀锌防腐","材质要求":"碳钢","备注":"膨胀体部分为M8螺栓，管卡部分为DN15卡箍，管卡与膨胀体总长度为175mm，整体材质均为碳钢，表面做热镀锌防腐处理。"} | 1000.00 | 个 | |
| 双头螺栓 | {"直径":"M20","长度":"90mm","螺纹长度":"≥35mm","材质":"碳钢","性能等级":"8.8","使用寿命":"730天","参照标准":"GB/T 9125-2010"} | 50.00 | 个 | |
| U型卡 | {"直径":"M8","长度":"60mm","材质":"Q235A","表面处理":"镀锌","使用寿命":"3650天","参照标准":"GB/T 3098.1-2010","备注":"带配套螺丝"} | 50.00 | 套 | |
| 防松螺母 | {"直径":"M30","材质":"中碳钢淬火并回火,紧锁塑圈材质尼龙","表面处理":"镀锌","性能等级":"8.8","特殊要求":"无","使用寿命":"180天","参照标准":"GB/T 3098.9-2020","备注":"验收:到货不合格供应商必须无条件退货或换货处理,所产生的费用由供货方承担."} | 50.00 | 个 | |
| 内六角螺丝 | {"直径":"M8","长度":"40mm","材质":"45H碳钢","表面处理":"中碳钢并热处理","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 70.1-2008","备注":"到货物资与技术要求不符，供应商应无理由退换货，产生的费用由供应商全部承担。"} | 400.00 | 个 | |
| 内六角螺丝 | {"直径":"M8","长度":"25MM","材质":"碳钢","性能等级":"12.9"} | 2600.00 | 根 | |
| 高强度螺栓 | {"直径":"M36","长度":"70mm","图号":"无","螺纹长度":"70mm","材质":"低碳合金钢","表面处理":"热处理发黑","性能等级":"8.8","使用寿命":"≥365天","参照标准":"GB/T 5783-2016","备注":"规格M36*70/8.8级,来货时表面涂防锈油防锈,如到货与技术要求不符,由供应商无条件进行退,换货处理"} | 50.00 | 个 | |
| 高强螺栓 | {"直径":"M22","长度":"80mm","图号":"无","螺纹长度":"40mm","材质":"螺栓:20MnTiB","表面处理":"渗硼","性能等级":"10.9","使用寿命":"9125天","特殊要求":"1杆配2垫1母","参照标准":"GB/T 1231-2006"} | 4130.00 | 套 | |
| 外六角螺栓 | {"直径":"M24","长度":"50mm","图号":"M24*50","螺纹长度":"50mm","材质":"碳钢","表面处理":"热处理(淬火、回火)","性能等级":"4.8","使用寿命":"≥365天","参照标准":"GB/T 5780-2016","备注":"到货不合格处理标准:如到货不符合技术要求,由供应商无条件进行更换,退货."} | 50.00 | 个 | |
| 止退螺帽 | {"直径":"M16","材质":"螺母材质Q235","表面处理":"镀锌","性能等级":"4.8级","特殊要求":"止退圈材质尼龙","使用寿命":"180天","参照标准":"GB/T 6182-2016","备注":"到货不符合技术要求，供货方负责退换货处理产生费用由供货方承担"} | 50.00 | 个 | |
| 方头螺栓 | {"直径":"M30","长度":"340mm","螺纹长度":"150mm","材质":"碳钢","表面处理":"发黑处理","性能等级":"4.8","使用寿命":"365天","备注":"方头厚度:20mm;长/宽:46mm"} | 50.00 | 个 | |
| 不锈钢拉铆钉 | {"规格型号":"M5*20/304","材质":"不锈钢304","使用寿命":"365天","参照标准":"GB/T 12617.1-2006"} | 10600.00 | 个 | |
| 钢结构用大六角头高强度螺栓连接副 | {"直径":"M20mm","长度":"70mm","材质":"螺栓：20MnTiB螺母：45#垫圈：45#"} | 50.00 | 套 | |
| 不锈钢双头螺栓 | {"直径":"M24","长度":"130mm","图号":"/","螺纹长度":"50mm","材质":"316L","表面处理":"无","性能等级":"8.8","使用寿命":"90天","特殊要求":"两端螺纹等长","参照标准":"GB/T 3106-2016","备注":"1、外观良好，无断丝，无错丝，无锈蚀痕迹等缺陷，到货时附带出厂合格证。\n2、如到货验收不符合技术要求，供货商无条件给予退换货处理，因此产生的费用由供货商承担。\n3、国产件，不限定品牌厂家。"} | 50.00 | 个 | |
| 不锈钢弹簧垫 | {"直径":"M8","材质":"65Mn","使用寿命":"730天"} | 50.00 | 个 | |
| 弹垫 | {"直径":"M6","材质":"65Mn","使用寿命":"730天"} | 50.00 | 个 | |
| 双头螺栓 | {"直径":"M34","长度":"175mm","图号":"/","螺纹长度":"60mm","材质":"碳钢","表面处理":"发黑","性能等级":"8.8","使用寿命":"90天","特殊要求":"无","参照标准":"GB/T 3098.1-2010","备注":"若产品达不到技术要求,由经销商无条件进行退换货处理."} | 50.00 | 个 | |
| 全丝螺杆 | {"直径":"M16","长度":"1000mm","材质":"碳钢","表面处理":"发黑","使用寿命":"90天","性能等级":"8.8","特殊要求":"无","参照标准":"GB/T 3098.1-2010","备注":"若产品达不到技术要求,由经销商无条件进行退换货处理."} | 10.00 | 个 | |
| 全丝螺杆 | {"直径":"M20","长度":"1000mm","材质":"碳钢","表面处理":"发黑","使用寿命":"90天","性能等级":"8.8","特殊要求":"无","参照标准":"GB/T 3098.1-2010","备注":"若产品达不到技术要求,由经销商无条件进行退换货处理."} | 60.00 | 个 | |
| 不锈钢螺母 | {"直径":"M24","高度":"22.3mm","材质":"316L","表面处理":"酸洗光亮","性能等级":"A4-50","使用寿命":"90天","参照标准":"GB/T 1229-2006","备注":"1、产品外观完好、无腐蚀、锈迹；\n2、如与技术要求不符，执行退换货处理，所产生的费用由供应商承担。"} | 350.00 | 个 | |
| 不锈钢外六角螺栓 | {"直径":"M16mm","长度":"150mm","图号":"M16*150","螺纹长度":"80mm","材质":"不锈钢304","表面处理":"不经处理","性能等级":"A2-50","使用寿命":"730天","参照标准":"GB/T 5782-2016","备注":"验货标准：1、外观应无破损、断裂、变形等外伤，物品尺寸规格应与上述技术要求相符,附带合格证。2、如到货物品与技术要求不符，厂家免费给予退换货。"} | 250.00 | 个 | |
| 沉头带榫螺栓 | {"直径":"M30","长度":"115mm","图号":"无","螺纹长度":"75mm","材质":"中碳钢","表面处理":"淬火并回火","性能等级":"8.8级","使用寿命":"1000天","参照标准":"GB/T 3098.1-2010","备注":"榫宽度5mm"} | 50.00 | 套 | |
| 螺帽 | {"直径":"M18","材质":"45#钢","性能等级":"10.9级","使用寿命":"60天"} | 7691.00 | 个 | |
| 螺母 | {"直径":"M42","材质":"Q235","性能等级":"4.8级","使用寿命":"3650天"} | 116.00 | 个 | |
| 高强螺母 | {"直径":"M20","材质":"低碳合金钢","性能等级":"10.9级","使用寿命":"365天"} | 4756.00 | 个 | |
| 螺母 | {"直径":"M27","材质":"45#钢","性能等级":"10.9级","使用寿命":"365天","参照标准":"GB/T 3098.1-2010"} | 854.00 | 个 | |
| 螺帽 | {"直径":"M36","材质":"35#","性能等级":"8.8级","使用寿命":"1095天"} | 1268.00 | 个 | |
| 外六角螺母 | {"直径":"M56","高度":"45mm","材质":"40Cr","性能等级":"10.9级","使用寿命":"365天"} | 50.00 | 个 | |
| 不锈钢外六角螺栓 | {"直径":"M16","长度":"100mm","材质":"304不锈钢","性能等级":"A2-50","使用寿命":"730天","参照标准":"GB/T 5782-2016"} | 100.00 | 个 | |
| 外六角螺丝 | {"直径":"M20","长度":"100mm","材质":"碳钢","性能等级":"4.8级","使用寿命":"365天","参照标准":"GB/T 5781-2016"} | 200.00 | 个 | |
| 高强外六角螺丝全丝 | {"直径":"M16","长度":"200mm","螺纹长度":"200mm","材质":"碳钢","性能等级":"8.8级","使用寿命":"60天"} | 400.00 | 个 | |
| 不锈钢螺栓 | {"直径":"M14","长度":"100mm","螺纹长度":"100mm","材质":"304不锈钢","性能等级":"A2-70","使用寿命":"365天","参照标准":"GB/T 3098.6-2014"} | 60.00 | 个 | |
| M4*30自攻丝 | {"直径":"M4","长度":"30mm","材质":"4.8级碳钢（渗碳钢）","表面处理":"平头十字槽口，表面度蓝锌，做钝化防锈处理","性能等级":"4.8级"} | 89100.00 | 个 | |
| 自攻丝 | {"直径":"M4","长度":"35mm","材质":"4.8级碳钢（渗碳钢）","表面处理":"平头十字槽口，表面度蓝锌，做钝化防锈处理。","性能等级":"4.8级"} | 25500.00 | 根 | |
| 镀锌自攻丝 | {"直径":"MM4","长度":"25mm","材质":"4.8级碳钢（渗碳钢）","表面处理":"平头十字槽口，表面度蓝锌，做钝化防锈处理。","性能等级":"4.8级"} | 126500.00 | 根 | |
| 钻尾自攻钉 | {"直径":"M5.5","长度":"25mm","材质":"CH1022A","表面处理":"平头十字槽口，表面度蓝锌，做钝化防锈处理。","性能等级":"4.8级","参照标准":"GB/T3098.11-2002"} | 81800.00 | 根 | |
| 膨胀螺栓 | {"直径":"M12","长度":"80mm","材质":"碳钢","使用寿命":"2920天"} | 50.00 | 个 | |
| 全丝螺栓 | {"直径":"M30","长度":"90mm","材质":"碳钢","使用寿命":"365天","性能等级":"8.8级"} | 30.00 | 个 | |
| 双头螺栓 | {"直径":"M18","长度":"200mm","材质":"碳钢","性能等级":"8.8级","使用寿命":"730天","参照标准":"GB/T 3098.1-2010"} | 50.00 | 个 | |
| 双头螺栓 | {"直径":"M24","长度":"190mm","材质":"碳钢","性能等级":"8.8级","使用寿命":"1825天"} | 50.00 | 个 | |
| 双头螺栓 | {"直径":"M27","长度":"180mm","材质":"45#钢","性能等级":"8.8级","使用寿命":"730天","参照标准":"GB/T 3098.1-2010"} | 50.00 | 个 | |
| 双头螺栓 | {"直径":"M30","长度":"140mm","材质":"35#钢","性能等级":"8.8级","使用寿命":"365天"} | 50.00 | 个 | |
| 双头螺栓 | {"直径":"M56","长度":"480mm","材质":"40Cr","性能等级":"10.9级","使用寿命":"365天"} | 50.00 | 个 | |
| 螺栓 | {"直径":"M8","长度":"30mm","材质":"Q235","性能等级":"4.8级","使用寿命":"730天"} | 660.00 | 根 | |
| 内六角螺栓 | {"直径":"M10","长度":"35mm","材质":"Q235","性能等级":"4.8级","使用寿命":"365天","参照标准":"GB/T 70.1-2008"} | 50.00 | 个 | |
| 内六角螺栓 | {"直径":"M12","长度":"40mm","材质":"碳钢","性能等级":"8.8级"} | 100.00 | 个 | |
| 螺栓 | {"直径":"M8","长度":"15mm","材质":"低碳钢","参照标准":"GB/T 5781-2016"} | 50.00 | 个 | |
| 螺栓 | {"直径":"M20","长度":"45mm","图号":"M20*45","螺纹长度":"45mm","材质":"35#钢","表面处理":"热处理发黑","性能等级":"8.8级","使用寿命":"365天","参照标准":"GB/T 5781-2016","备注":"特殊要求：外六角,全丝,外观良好，无断丝，无错丝，无锈蚀痕迹等缺陷.验货要求:如到货与技术要求不符,由供应商无条件进行退,换货处理."} | 200.00 | 个 | |
| 高强度螺栓 | {"直径":"M24","长度":"80mm","螺纹长度":"80mm","材质":"35#钢","性能等级":"8.8级","使用寿命":"365天","参照标准":"GB/T 5781-2016"} | 50.00 | 个 | |
| 沉头十字螺栓 | {"直径":"M10mm","长度":"20mm","材质":"304","使用寿命":"720天"} | 50.00 | 个 | |
| 不锈钢双头螺栓 | {"直径":"M20mm","长度":"100mm","材质":"316L","使用寿命":"365天"} | 50.00 | 个 | |
| 高压双头螺栓 | {"直径":"M24mm","长度":"100mm","材质":"碳钢","性能等级":"8.8","使用寿命":"720天"} | 50.00 | 个 | |
| 不锈钢螺丝 | {"直径":"M10","长度":"50mm","图号":"无","螺纹长度":"50mm","材质":"不锈钢304","表面处理":"无","性能等级":"A2-70","使用寿命":"180天","参照标准":"GB/T 3098.6-2014","备注":"不符合技术要求,免费退换货."} | 1614.00 | 个 | |
| 不锈钢螺栓 | {"直径":"M14","长度":"70mm","图号":"无","螺纹长度":"70mm","材质":"不锈钢304","表面处理":"无","性能等级":"A2-70","使用寿命":"365天","参照标准":"GB/T 3098.6-2014","备注":"不符合技术要求,免费退换货."} | 50.00 | 个 | |
| 不锈钢螺帽 | {"直径":"M14","高度":"10.3mm","材质":"不锈钢304","表面处理":"无","性能等级":"A2-70","使用寿命":"730天","参照标准":"GB/T 3098.15-2014","备注":"不符合技术要求,进行退换货。"} | 428.00 | 个 | |
| 不锈钢平垫 | {"直径":"M14","厚度":"2.5mm","材质":"不锈钢304","表面处理":"无","性能等级":"A2","使用寿命":"360天","参照标准":"GB/T 3098.26-2021","备注":"不符合技术要求,进行退换货."} | 8692.00 | 个 | |
| 高强度双头螺栓 | {"直径":"M24","长度":"120mm","图号":"无","螺纹长度":"45mm","材质":"碳钢","表面处理":"发黑处理","性能等级":"8.8","使用寿命":"730天","特殊要求":"无","参照标准":"GB/T 3098.1-2010","备注":"不符合技术要求,免费退换货."} | 50.00 | 根 | |
| 内六角螺栓 | {"直径":"M30","长度":"430mm","图号":"无","螺纹长度":"110mm","材质":"40Cr","表面处理":"发黑","性能等级":"8.8级","使用寿命":"730天","特殊要求":"外观良好，无错丝无裂纹等缺陷，如到货不符合技术要求，由供应商无条件进行更换、退货","参照标准":"GB/T 16938-2008"} | 20.00 | 个 | |
| 内六角螺丝 | {"直径":"M16","长度":"70mm","螺纹长度":"70mm","材质":"45H碳钢","性能等级":"12.9","使用寿命":"365天","参照标准":"GB/T 3098.1-2010"} | 758.00 | 个 | |
| 弹性圆柱销 | {"规格型号":"6*12","材质":"弹簧钢"} | 100.00 | 个 | |
| 外六角螺丝 | {"直径":"M16","长度":"60mm","图号":"M16*60","螺纹长度":"60mm","材质":"碳钢","表面处理":"镀锌","性能等级":"4.8","使用寿命":"≥365天","参照标准":"GB/T 16938-2008","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} | 50.00 | 个 | |
| 螺栓 | {"直径":"M24","长度":"100mm","图号":"M24*100","螺纹长度":"100mm","材质":"中碳钢并经热处理（淬火、回火）","表面处理":"发黑处理","性能等级":"8.8","使用寿命":"≥730天","参照标准":"GB/T 16938-2008","备注":"1、外观良好，无断丝，错丝\n2、到货验收不符合要求，退换货处理，产生费用供应商承担"} | 50.00 | 个 | |
| 外六角螺栓 | {"直径":"M20","长度":"260mm","螺纹长度":"80±5mm","材质":"低碳合金钢，淬火并回火","性能等级":"8.8"} | 50.00 | 个 | |
| 外六角螺栓 | {"直径":"M20","长度":"40mm","螺纹长度":"40mm","材质":"碳钢","性能等级":"8.8"} | 25.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M3","长度":"5mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 100.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M3","长度":"8mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 100.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M4","长度":"8mm","材质":"304不锈钢","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014"} | 500.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M5","长度":"8mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 50.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M5","长度":"10mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 1600.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M5","长度":"20mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 100.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M6","长度":"12mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 1000.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M6","长度":"15mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 900.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M6","长度":"25mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 500.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M6","长度":"40mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 1380.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M8","长度":"12mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 11950.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M8","长度":"45mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 800.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M8","长度":"55mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 400.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M8","长度":"85mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准：必须符合以上技术要求，不符合技术要求，退换货，产生的费用，由供货方承担。"} | 760.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M8","长度":"90mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 400.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M8","长度":"100mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准:必须符合以上技术要求,不符合技术要求,退换货,产生的费用,由供货方承担."} | 50.00 | 个 | |
| 不锈钢内六角螺丝 | {"直径":"M8","长度":"120mm","材质":"304不锈钢","表面处理":"表面光洁无刺","性能等级":"A2-70","使用寿命":"60天","参照标准":"GB/T 3098.6-2014","备注":"验收标准：必须符合以上技术要求，不符合技术要求，退换货，产生的费用，由供货方承担。"} | 250.00 | 个 | |
| 外六角螺栓 | {"直径":"M18","长度":"172mm","材质":"碳钢","性能等级":"8.8"} | 50.00 | 个 | |
| 外六角螺栓 | {"直径":"M18","长度":"242mm","图号":"无","螺纹长度":"130mm","材质":"碳钢","表面处理":"发黑处理","性能等级":"8.8","使用寿命":"365天","参照标准":"GB/T 5782-2016"} | 50.00 | 个 | |
| 外六角螺栓 | {"直径":"M24","长度":"140mm","材质":"碳钢","性能等级":"8.8"} | 347.00 | 个 | |
| 外六角螺栓 | {"直径":"M24","长度":"150mm","材质":"碳钢","性能等级":"8.8"} | 50.00 | 个 | |
| 内六角螺丝 | {"直径":"M16","长度":"40mm","材质":"碳钢","表面处理":"表面黑化处理","性能等级":"8.8级","使用寿命":"365天","参照标准":"GB/T 16938-2008","备注":"外观良好,无断丝,错丝,到货提供材质和质量合格证,到货不符合要求,予以退换货处理,产生费用供应商承担."} | 50.00 | 个 | |
| 外六角螺栓 | {"直径":"M24","长度":"177mm","材质":"碳钢","性能等级":"8.8"} | 50.00 | 个 | |
| 外六角螺栓 | {"直径":"M10","长度":"20mm","螺纹长度":"20mm","材质":"碳钢","表面处理":"淬火,调质","性能等级":"8.8级","使用寿命":"365天"} | 5664.00 | 个 | |
| 不锈钢平垫 | {"直径":"M12","材质":"碳钢","使用寿命":"180天"} | 50.00 | 个 | |
| 不锈钢平垫 | {"直径":"M16","厚度":"3","材质":"不锈钢304","使用寿命":"＞365天"} | 542.00 | 个 | |
| 平垫 | {"直径":"M27","材质":"碳钢","性能等级":"8.8","使用寿命":"180天"} | 200.00 | 个 | |
| 膨胀螺栓 | {"规格型号":"5.5*115","直径":"5.5mm","长度":"115mm","强度等级":"10.9","表面处理":"丝扣均匀,无断丝,缺丝","材质要求":"白铁电镀"} | 78000.00 | 个 | |
| 镀锌丝杆 | {"规格型号":"Φ10*990mm","直径":"10mm","长度":"990mm","强度等级":"10.9","表面处理":"丝扣均匀,无缺丝,断丝,缺丝","材质要求":"铁镀锌"} | 5471.00 | 米 | |
| 不锈钢自攻钉 | {"长度":"50mm","直径":"4.8mm","表面处理":"不锈钢原色","材质":"不锈钢304","允许偏差":"±0.2㎜","特殊要求":"到货与技术要求不符退换货处理，产生费用供货方承担。","参照标准":"GB/T 3098.21-2014","备注":"自攻螺钉外观应光洁、无毛刺、飞边，丝扣均匀，断丝、缺丝、十字封堵、尖偏、偏心等不合格率＜5%。"} | 50000.00 | 个 | |
| 不锈钢自攻钉 | {"长度":"35mm","直径":"4.8mm","表面处理":"不锈钢原色","材质":"不锈钢304","允许偏差":"±0.2㎜","特殊要求":"自攻钉无钉口封堵现象","参照标准":"GB/T 3098.21-2014","备注":"自攻螺钉外观应光洁、无毛刺、飞边，丝扣均匀，断丝、缺丝、十字封堵、尖偏、偏心等不合格率＜5%。到货与技术要求不符退换货处理，产生费用有供货方承担。"} | 80800.00 | 个 | |
| 十字槽沉头自攻螺丝 | {"长度":"18mm","直径":"4.8mm","表面处理":"不锈钢原色","材质":"不锈钢304","允许偏差":"±0.2㎜","特殊要求":"到货与技术要求不符退换货处理，产生费用供货方承担","参照标准":"GB/T 3098.21-2014","备注":"螺丝丝扣均匀，无断丝、缺丝现象，自攻钉无顶口封堵现象。使用年限五年以上。"} | 104000.00 | 个 | |
| 十字槽沉头自攻螺丝 | {"长度":"19mm","直径":"3.8mm","表面处理":"不锈钢原色","材质":"不锈钢304","允许偏差":"±0.2㎜","特殊要求":"到货与技术要求不符退换货处理，产生费用供货方承担。","参照标准":"GB/T 3098.21-2014","备注":"螺丝丝扣均匀,无缺丝,断丝现象，自攻钉无顶口封堵现象，使用年限5年以上。"} | 189400.00 | 个 | |
| 抽芯拉铆钉 | {"规格型号":"Φ5*20","材质":"铝壳铁芯","使用寿命":"365天","参照标准":"GBT 3098.19-2004"} | 10000.00 | 个 | |
| 不锈钢内六角螺栓 | {"直径":"M16","长度":"35mm","螺纹长度":"35mm","材质":"316L","使用寿命":"1460天","参照标准":"GB/T 3106-2016"} | 50.00 | 个 | |
| 不锈钢外六角螺丝 | {"直径":"M10","长度":"30","螺纹长度":"30mm","材质":"不锈钢304","性能等级":"A2-70","使用寿命":"365天"} | 41932.00 | 个 | |
| 外六角螺栓 | {"直径":"M12","长度":"80mm","材质":"碳钢","性能等级":"8.8级","使用寿命":"365天","参照标准":"GB/T 5782-2016"} | 50.00 | 个 | |
| 外六角螺栓 | {"直径":"M14","长度":"30mm","材质":"碳钢","性能等级":"8.8级","使用寿命":"180天"} | 50.00 | 个 | |
| 外六角螺栓 | {"直径":"M16","长度":"60mm","材质":"45#钢","性能等级":"8.8级","使用寿命":"90天"} | 1060.00 | 个 | |
| 外六角螺栓 | {"直径":"M20","长度":"55mm","材质":"Q235","性能等级":"4.8级","使用寿命":"365天","参照标准":"GB/T 5780-2016"} | 2400.00 | 个 | |
| 外六角螺栓 | {"直径":"M27","长度":"90mm","螺纹长度":"40mm","材质":"45#钢","表面处理":"氧化发黑","性能等级":"8.8级","使用寿命":"180天","参照标准":"GB/T 3098.1-2010"} | 150.00 | 个 | |
| 外六角螺栓 | {"直径":"M30","长度":"100mm","材质":"碳钢","性能等级":"8.8级","使用寿命":"365天","参照标准":"GB/T 18230-2000"} | 50.00 | 个 | |
| 高强螺栓 | {"直径":"M20","长度":"50mm","材质":"螺栓20MnTiB、螺母45#钢、垫圈45#钢","性能等级":"10.9级","使用寿命":"9125天"} | 3380.00 | 套 | |
| 外六角螺丝 | {"直径":"M14","长度":"70mm","材质":"碳钢","性能等级":"8.8级","使用寿命":"365天"} | 200.00 | 套 | |
| 外六角螺丝 | {"直径":"M16","长度":"90mm","材质":"20#钢","性能等级":"4.8级","使用寿命":"365天"} | 2100.00 | 套 | |
| 投标厂商资质 | | 注册资金 | | 专业资质 | | | 公司业绩 | | | 相关认证 | | | 其他 |
|
换一批
换一批